cisco-GNS3-pix防火墙基本配置实操(持续更新)

其他 2020-04-01 17:17:41 阅读次数: 0

一、ASA和PIX基础配置

1、ASA防火墙配置

1、GNS配置

因为使用的GNS3的版本可能不同，gns配置asa防火墙的步骤可能不同

在低版本的gns中直接在qemu选项里可以直接配置,参考：https://blog.51cto.com/dldxzjr/1905682

在高版本的gns中配置可以参考：https://wenku.baidu.com/view/8934accc48649b6648d7c1c708a1284ac850059c.html

2、简单的防火墙设置命令

show version
show running-config
show activation-key			查看激活秘钥
activation-key key-values		设置激活秘钥
write mem					将配置保存到非易失flash，重启或断电都不会对配置产生影响
no shutdown					使借口处于启用

show interface ip breif			提供接口的简短概要
interface 接口
nameif inside/outside/dmz
ip address ip地址 掩码
speed auto					#连接速度，有10/100/1000Mbps等
duplex auto					#双工模式，有Half/Full为半双工/全双工模式
						   #一般网卡都为Auto/Auto适配出来的情况一般为100M全双工模式

#防火墙上设置静态路由，最多可以配置3个不同的默认路由
例：
指向外部接口上的网关192.168.1.1的路由	route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
可通过内部接口上的网关192.168.254.2找到网络172.21.0.0/16		route inside 172.21.0.0 255.255.0.0 192.168.254.2 1
删除则直接加一个no
show route


#
show xlate
show conn

实例：

###配置ASA防火墙

ciscoasa# show int ip b
Interface                  IP-Address      OK? Method Status                Protocol
GigabitEthernet0           unassigned      YES unset  administratively down up
GigabitEthernet1           unassigned      YES unset  administratively down up
GigabitEthernet2           unassigned      YES unset  administratively down up
GigabitEthernet3           unassigned      YES unset  administratively down up
ciscoasa# conf t
ciscoasa(config)# int g0
ciscoasa(config-if)# nameif inside
INFO: Security level for "inside" set to 100 by default.
ciscoasa(config-if)# ip address 13.0.1.1 255.255.255.0
ciscoasa(config-if)# no sh
ciscoasa(config-if)# show int ip b
Interface                  IP-Address      OK? Method Status                Protocol
GigabitEthernet0           13.0.1.1        YES manual up                    up
GigabitEthernet1           unassigned      YES unset  administratively down up
GigabitEthernet2           unassigned      YES unset  administratively down up
GigabitEthernet3           unassigned      YES unset  administratively down up




###配置pc1的ip

PC1> show ip

NAME        : PC1[1]
IP/MASK     : 0.0.0.0/0
GATEWAY     : 0.0.0.0
DNS         :
MAC         : 00:50:79:66:68:00
LPORT       : 10012
RHOST:PORT  : 127.0.0.1:10011
MTU:        : 1500

PC1> ip 13.0.1.2 13.0.1.1 24
Checking for duplicate address...
PC1 : 13.0.1.2 255.255.255.0 gateway 13.0.1.1

PC1> show ip

NAME        : PC1[1]
IP/MASK     : 13.0.1.2/24
GATEWAY     : 13.0.1.1
DNS         :
MAC         : 00:50:79:66:68:00
LPORT       : 10012
RHOST:PORT  : 127.0.0.1:10011
MTU:        : 1500

PC1>

ping测试：

2、pix防火墙配置

安装时有一步需要激活

activation-key key

关闭重启pix防火墙：

还有一点需要注意，就是pix运行时有一个进程pemu会占用大量的cpu资源，导致很卡，可以使用BES对它进行限制：

实例

pix：

pixfirewall> en
Password:
pixfirewall# conf t
pixfirewall(config)# exit
pixfirewall# show int ip b
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0                  unassigned      YES unset  administratively down down
Ethernet1                  unassigned      YES unset  administratively down down
Ethernet2                  unassigned      YES unset  administratively down down
Ethernet3                  unassigned      YES unset  administratively down down
Ethernet4                  unassigned      YES unset  administratively down down
pixfirewall# conf t
pixfirewall(config)# int e0
pixfirewall(config-if)# ip address 13.0.1.1 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# show int ip b
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0                  unassigned      YES manual up                    up
Ethernet1                  unassigned      YES unset  administratively down down
Ethernet2                  unassigned      YES unset  administratively down down
Ethernet3                  unassigned      YES unset  administratively down down
Ethernet4                  unassigned      YES unset  administratively down down
pixfirewall(config-if)# nameif inside
INFO: Security level for "inside" set to 100 by default.
pixfirewall(config-if)# show int ip b
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0                  13.0.1.1        YES manual up                    up
Ethernet1                  unassigned      YES unset  administratively down down
Ethernet2                  unassigned      YES unset  administratively down down
Ethernet3                  unassigned      YES unset  administratively down down
Ethernet4                  unassigned      YES unset  administratively down down

pc1

VPCS[1]> ip 13.0.1.2 13.0.1.1 24
Checking for duplicate address...
PC1 : 13.0.1.2 255.255.255.0 gateway 13.0.1.1

VPCS[1]> show ip

NAME        : VPCS[1]
IP/MASK     : 13.0.1.2/24
GATEWAY     : 13.0.1.1
DNS         :
MAC         : 00:50:79:66:68:00
LPORT       : 20000
RHOST:PORT  : 127.0.0.1:30000
MTU:        : 1500

VPCS[1]>

ping

二、PIX-NAT

1、pix配置动态NAT

基础命令举例：

show int ip b
hostname
ip address
nameif
security number

show conn					显示所有的活动连接
show conn detail
show local-host
show xlate					显示翻译(xlate)槽位的内容
show xlate detail

#添加acl,访问规则
1)创建标准访问列表
access-list [list-number] [permit|deny] [source-address] [wildcard mask] [log]
access-group list-number in int 接口名



#静态NAT
static [(internal_if_name, external_if_name)] global_ip local_ip[netmask network_mask][max_conns
[em_limit]] [norandomseq]
例：static (inside,outside) 13.0.1.3 192.168.1.2 				将本地地址192.168.1.2转换为全局地址13.0.1.3

#static PAT
static [(real_interface, mapped_interface)] {tcp | udp} {mapped_ip | interface}
mapped_port {real_ip real_port [netmask mask]

例：dmz:172.16.1.9  outside:192.168.0.9
static (dmz,outside) tcp 192.168.0.9 ftp 172.16.1.9 ftp netmask 255.255.255.255

#动态NAT
nat (inside) 1 192.168.1.0 255.255.255.0
global (outside) 1 12.0.1.0-12.0.1.9 netmask 255.255.255.0

#PAT
nat (inside) 1 192.168.1.0 255.255.255.0
global (outside) 1 12.0.1.9 netmask 255.255.255.0

#nat 0
nat (dmz) 0 192.168.0.9 255.255.255.255
#
no global (outside) 1 12.0.1.0-12.0.1.9 netmask 255.255.255.0


route if_name ip_address netmask gateway_ip [metric]			为接口口if_name定义一条静态或缺省路由

#
debug icmp trace
no debug icmp trace

#
logging on
show logging
no logging on
show capture inside

#
show users
show run nat-control
show conn detail
show xlate

pix配置

pixfirewall> en
Password:
pixfirewall# conf t
pixfirewall(config)# int e0
pixfirewall(config-if)# ip address 192.168.1.1 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# int e1
pixfirewall(config-if)# ip address 13.0.1.1 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# exit
pixfirewall(config)# exit
pixfirewall# show int ip b
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0                  unassigned      YES manual up                    up
Ethernet1                  unassigned      YES manual up                    up
Ethernet2                  unassigned      YES unset  administratively down down
Ethernet3                  unassigned      YES unset  administratively down down
Ethernet4                  unassigned      YES unset  administratively down down
pixfirewall# conf t
pixfirewall(config)# int e0
pixfirewall(config-if)# nameif inside
INFO: Security level for "inside" set to 100 by default.
pixfirewall(config-if)# int e1
pixfirewall(config-if)# nameif outside
INFO: Security level for "outside" set to 0 by default.
pixfirewall(config-if)# exit
pixfirewall(config)# exit
pixfirewall# show int ip b
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0                  192.168.1.1     YES manual up                    up
Ethernet1                  13.0.1.1        YES manual up                    up
Ethernet2                  unassigned      YES unset  administratively down down
Ethernet3                  unassigned      YES unset  administratively down down
Ethernet4                  unassigned      YES unset  administratively down down
pixfirewall# conf t
pixfirewall(config)# access-list test1 permit icmp any any
pixfirewall(config)# access-group test1 in int outside
pixfirewall(config)# nat (inside) 1 192.168.1.0 255.255.255.0
pixfirewall(config)# global (outside) 1 13.0.1.4-13.0.1.6 netmask 255.255.255.0

R1

R1#ip route 0.0.0.0 0.0.0.0 192.168.1.1
!因为我们是用路由器R1模拟的主机，所以要么关闭路由功能，配置网关；要么添加一条路由让路由器发出的消息从192.168.1.1出去

2、static NAT

pix配置

pixfirewall> en
Password:
pixfirewall# conf t
pixfirewall(config)# int e0
pixfirewall(config-if)# ip address 192.168.1.1 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# int e1
pixfirewall(config-if)# ip address 13.0.1.1 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# int e0
pixfirewall(config-if)# nameif inside
INFO: Security level for "inside" set to 100 by default.
pixfirewall(config-if)# int e1
pixfirewall(config-if)# nameif outside
INFO: Security level for "outside" set to 0 by default.
pixfirewall(config-if)# exit

pixfirewall(config)# show running-config static
pixfirewall(config)# static (inside,outside) 13.0.1.3 192.168.1.2
pixfirewall(config)# static (inside,outside) 13.0.1.4 192.168.1.3
pixfirewall(config)# route outside 0 0 13.0.1.2
pixfirewall(config)# exit
pixfirewall# show int ip b
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0                  192.168.1.1     YES manual up                    up
Ethernet1                  13.0.1.1        YES manual up                    up
Ethernet2                  unassigned      YES unset  administratively down down
Ethernet3                  unassigned      YES unset  administratively down down
Ethernet4                  unassigned      YES unset  administratively down down

pixfirewall(config)# access-l
pixfirewall(config)# access-list acl-outside permit icmp any any
pixfirewall(config)# access-g
pixfirewall(config)# access-group acl-outside in int outside
pixfirewall(config)# exit
pixfirewall# show int ip b
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0                  192.168.1.1     YES manual up                    up
Ethernet1                  13.0.1.1        YES manual up                    up
Ethernet2                  unassigned      YES unset  administratively down down
Ethernet3                  unassigned      YES unset  administratively down down
Ethernet4                  unassigned      YES unset  administratively down down



测试：
pixfirewall# ping 13.0.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 13.0.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 10/14/20 ms
pixfirewall# ping 192.168.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 10/10/10 ms
pixfirewall# show running-config
: Saved
:
PIX Version 7.2(2)
!
hostname pixfirewall
enable password 8Ry2YjIyt7RRXU24 encrypted
names
!
interface Ethernet0
 nameif inside
 security-level 100
 ip address 192.168.1.1 255.255.255.0
!
interface Ethernet1
 nameif outside
 security-level 0
 ip address 13.0.1.1 255.255.255.0
!
interface Ethernet2
 shutdown
 no nameif
 no security-level
 no ip address
!
interface Ethernet3
 shutdown
 no nameif
 no security-level
 no ip address
!
interface Ethernet4
 shutdown
 no nameif
 ...
pixfirewall#

R1配置

R1#en
R1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R1(config)#int f0/0
R1(config-if)#ip address 13.0.1.2 255.255.255.0
R1(config-if)#no sh
R1(config-if)#
*Mar  1 00:19:52.959: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:19:53.959: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R1(config-if)#int f1/0
R1(config-if)#ip address 14.0.1.1 255.255.255.0
R1(config-if)#no sh
R1(config-if)#
*Mar  1 00:25:10.991: %LINK-3-UPDOWN: Interface FastEthernet1/0, changed state to up
*Mar  1 00:25:11.991: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
R1(config-if)#

pc1\pc2\pc3配置

ping测试

192.168.1.2 ping 13.0.1.2

192.168.1.3 ping 14.0.1.2

14.0.1.2 ping 192.168.1.2

3、PAT

类似于动态NAT，只不过外部地址池里只有一个公网ip，主要是通过网络套接字(ip+端口的方式)实现地址转换

4、pix防火墙----二接口测试(inside,outside)

。。好几天没有打开GNS3，发现前面的ios配置全没了。老老实实又重新配置了一遍

R1配置

R1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R1(config)#int f1/0
R1(config-if)#ip address 192.168.1.1 255.255.255.0
R1(config-if)#no sh
R1(config-if)#
*Mar  1 00:01:04.391: %LINK-3-UPDOWN: Interface FastEthernet1/0, changed state to up
*Mar  1 00:01:05.391: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
R1(config-if)#int f0/0
R1(config-if)#ip address 13.0.1.2 255.255.255.0
R1(config-if)#no sh
R1(config-if)#
*Mar  1 00:01:42.527: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:01:43.527: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R1(config-if)#exit
R1(config)#ip route 14.0.1.0 255.255.255.0 13.0.1.1
R1(config)#ip route 15.0.1.0 255.255.255.0 13.0.1.1

PC1、PC2、PC3、PC4配置

VPCS[1]> ip 192.168.1.2 192.168.1.1 24
Checking for duplicate address...
PC1 : 192.168.1.2 255.255.255.0 gateway 192.168.1.1

VPCS[1]> 2
VPCS[2]> ip 192.168.1.3 192.168.1.1 24
Checking for duplicate address...
PC2 : 192.168.1.3 255.255.255.0 gateway 192.168.1.1

VPCS[2]> 3
VPCS[3]> ip 15.0.1.2 15.0.1.1 24
Checking for duplicate address...
PC3 : 15.0.1.2 255.255.255.0 gateway 15.0.1.1

VPCS[3]> 4
VPCS[4]> ip 15.0.1.3 15.0.1.1 24
Checking for duplicate address...
PC4 : 15.0.1.3 255.255.255.0 gateway 15.0.1.1

VPCS[4]>

R2配置

R2#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R2(config)#int f0/0
R2(config-if)#ip address 14.0.1.2 255.255.255.0
R2(config-if)#no sh
R2(config-if)#
*Mar  1 00:00:51.907: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar  1 00:00:52.907: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R2(config-if)#int f1/0
R2(config-if)#ip address 15.0.1.1 255.255.255.0
R2(config-if)#no sh
R2(config-if)#exit

R2(config)#ip route 13.0.1.0 255.255.255.0 14.0.1.1
R2(config)#ip route 192.168.1.0 255.255.255.0 14.0.1.1


#可以给路由器配置远程终端，用telnet来丰富一下测试
R2#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R2(config)#line vty 0 4
R2(config-line)#password zwish
R2(config-line)#end
R2#
*Mar  1 01:35:20.871: %SYS-5-CONFIG_I: Configured from console by console
R2#

PIX配置

pixfirewall# conf t
pixfirewall(config)# int e0
pixfirewall(config-if)# ip address 13.0.1.1 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# nameif inside
INFO: Security level for "inside" set to 100 by default.
pixfirewall(config-if)# int e1
pixfirewall(config-if)# ip address 14.0.1.1 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# nameif outside
INFO: Security level for "outside" set to 0 by default.

pc1、R1先ping一下pix的e0，看一下能不能通，可以再继续

pixfirewall(config-if)# access
pixfirewall(config-if)# access-
pixfirewall(config-if)# access-l
pixfirewall(config-if)# access-list acl-1 permit icmp any any
pixfirewall(config)# access-g
pixfirewall(config)# access-group acl-1 in int
pixfirewall(config)# access-group acl-1 in interface outside
pixfirewall(config)# nat (inside) 1 0 0
pixfirewall(config)# global (outside) 1 14.0.1.3-14.0.1.6 netmask 255.255.255.0
#下面是配置回程路由
pixfirewall(config)# route inside 192.168.1.0 255.255.255.0 13.0.1.2
pixfirewall(config)# route outside 15.0.1.0 255.255.255.0 14.0.1.2		
pixfirewall(config)#

测试

pc1 ping R2

pc1 ping pc3

pc3 ping pc1

R1 telnet 登录R2 (因为我没有用路由器模拟主机，所以用的R1，如果是路由器模拟的主机，则直接用PC1进行telnet登录)

猜你喜欢

转载自www.cnblogs.com/zw1sh/p/12613843.html
今日推荐
基于大语言模型的开源知识库问答系统 MaxKB GitHub Star 数量突破 5,000 个！
美国拟限制 AI 大模型出口中国和俄罗斯
苹果将与 OpenAI 达成协议，将 ChatGPT 应用于 iPhone
openKylin 社区生态委员会第六次会议圆满召开
阿里云正式发布通义千问 2.5
Python 3.13 发布首个 Beta：实验性自由线程模式和 JIT、改进交互式解释器
Stack Overflow 拿我的代码去训练 AI 大模型，还封了我的账号
Pop!_OS 的 COSMIC 桌面完成 App Store 上架工作
《2024 年一季度互联网投融资运行情况》研究报告
报告：Django 仍然是 74% 开发者的首选
15 年前上了“FFmpeg 耻辱柱”，今天他还得谢谢咱——腾讯QQPlayer一雪前耻？
TIOBE 5 月榜单：Fortran “复活”进入 Top 10
周排行
记一下去大梅沙的准备（2018-05-26）
Spring 注解 事务
基于HTTP协议的客户端缓存
阿里云rds 备份和还原
[PHP] 几个拖慢 PHP 程序/API 运行速度的点
python 代码风格------------PEP8规则
js控制json生成菜单——自制菜单（一）
将字符串: 'k:1|k1:2|k2:3|k3:4 ' ,处理成 python 字典: {'k':1, 'k1':2, ...}
微信小程序转支付宝小程序
Qt551.窗口滚动条
每日归档
更多
2024-05-13(18)
2024-05-12(0)
2024-05-11(38)
2024-05-10(38)
2024-05-09(35)
2024-05-08(42)
2024-05-07(14)
2024-05-06(40)
2024-05-05(0)
2024-05-04(7)

代码天地 © 2018 codetd.com

境外服务器   最新电视剧2022