1.查看网络MAC地址
[root@centos ~]# cat /etc/udev/rules.d/70-persistent-net.rules
显示如下信息
# PCI device 0x15ad:0x07b0 (vmxnet3)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:50:56:94:04:3c", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
# PCI device 0x15ad:0x07b0 (vmxnet3)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:50:56:94:53:24", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"
eth0:对应第一张网卡,eth1:对就第二张网卡。当前使用eth0连接路由器,eth1保留(服务器一般用来,连接其它主机)
2.修改主机名称
[root@centos ~]# vim /etc/sysconfig/network
打开文件,修改以下内容并保存
NETWORKING=yes #使用网络
HOSTNAME=centos #设置主机名称
3.修改网卡
[root@centos ~]# vim /etc/sysconfig/network-scripts/ifcfg-eth0
打开文件,修改以下内容并保存
DEVICE=eth0 #对应第一张网卡
HWADDR=00:50:56:94:04:3C #必须对应etho是的MAC地址(/etc/udev/rules.d/70-persistent-net.rules)
TYPE=Ethernet #网卡类型
UUID=b79**** #这是自动生成的
ONBOOT=yes #是否启动时运行
NM_CONTROLLED=yes
BOOTPROTO=static #启用地址协议 --static:静态协议 --bootp协议 --dhcp协议
#以上是系统自带的,下面是手动添加的。
DEFROUTE=yes
IPV4_FAILURE_FATAL=yes
IPV6INIT=no
NAME="System eth0" #名称
PEERDNS=yes
PEERROUTES=yes
IPADDR=192.168.1.253 #指定本机IP地址
NETMASK=255.255.255.0 #指定子网掩码
GATEWAY=192.168.1.1 指定网关
4.修改DNS
[root@centos ~]# vim /etc/resolv.conf
打开文件,修改以下内容并保存
nameserver 8.8.8.8 #GOOGLE的DNS服务器
nameserver 61.144.56.100 #指定当前城市最近的DNS服务器(各城市不一样,上网搜索)
nameserver 192.168.1.1 #指定经路由器上指定的DNS服务器
5.重新启动网络配置
[root@centos ~]#service network restart
注:
如果出现提示Determining if ip address X.X.X.X is already in use for device eth0。
是因为linux网卡配置arp检查导致的,把这个关掉即可。
在网卡配置文件里面添加 ARPCHECK=no , 然后再重新执行 service network restart 即可。
执行 restart 后 /etc/resolv.conf 文件可能会被覆盖掉,需要将这个的属性设置为只读,只有 root 用户可以修改。
具体办法是运行以下命令:
$ chattr +i /etc/resolv.conf , 该命令修改文件属性为只有 root 用户才能修改该文件。去掉可将参数改为 “-i”。
或者重启网卡
[root@centos ~]# /etc/init.d/network stop
[root@centos ~]# /etc/init.d/network start
6.重启
[root@centos ~]#shutdown -r now
7.查看当前IP设置
[root@centos ~]# ifconfig
如果仍然只有 lo而没有 eth0 则说明eth0 没有启动
激活eth0 [root@centos ~]# ifup eth0 #启动网络
8.测试是否连接外网
[root@centos ~]# ping www.163.com
网卡接口关闭与激活
[root@centos ~]# ifdown eth0 #关闭网络
[root@centos ~]# ifup eth0 #启动网络
网络服务启动与关闭
方法一:
[root@centos ~]# service network stop #关闭网络服务
[root@centos ~]# service network start #启动网络服务
[root@centos ~]# service network restart #重启网络服务
方法二:
[root@centos ~]# /etc/init.d/network stop
[root@centos ~]# /etc/init.d/network start
[root@centos ~]# /etc/init.d/network restart
网卡状态查询
[root@centos ~]# service network status
Configured devices:
lo eth0
Currently active devices:
lo eth0
临时配置网卡信息,无需重启。
[root@centos ~]# ifconfig eth0 10.1.1.10 netmask 255.0.0.0
查看网卡接口信息,默认列出所有接口
[root@centos ~]# ifconfig
查看当前路由及网关信息
[root@centos ~]# netstat -r
----------------------------------------------------------------
以下是参考,如果按上面步骤不行,可以详细看以下内容:
网络接口配置文件
[root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0
# Intel Corporation 82545EM Gigabit Ethernet Controller (Copper)
TYPE=Ethernet #网卡类型
DEVICE=eth0 #网卡接口名称
ONBOOT=yes #系统启动时是否自动加载
BOOTPROTO=static #启用地址协议 --static:静态协议 --bootp协议 --dhcp协议
IPADDR=192.168.1.11 #网卡IP地址
NETMASK=255.255.255.0 #网卡网络地址
GATEWAY=192.168.1.1 #网卡网关地址
DNS1=10.203.104.41 #网卡DNS地址
HWADDR=00:0C:29:13:5D:74 #网卡设备MAC地址
BROADCAST=192.168.1.255 #网卡广播地址
重新导入ifcfg-eth0网络配置文件
[root@localhost ~]# /etc/init.d/network reload
Shutting down interface eth0: [ OK ]
Shutting down loopback interface: [ OK ]
Bringing up loopback interface: [ OK ]
Bringing up interface eth0: [ OK ]
网卡接口关闭与激活
[root@localhost ~]# ifdown eth0 #关闭网络
[root@localhost ~]# ifup eth0 #启动网络
网络服务启动与关闭
方法一:
[root@localhost ~]# service network stop #关闭网络服务
[root@localhost ~]# service network start #启动网络服务
[root@localhost ~]# service network restart #重启网络服务
方法二:
[root@localhost ~]# /etc/init.d/network stop
[root@localhost ~]# /etc/init.d/network start
[root@localhost ~]# /etc/init.d/network restart
网卡状态查询
[root@localhost ~]# service network status
Configured devices:
lo eth0
Currently active devices:
lo eth0
临时配置网卡信息,无需重启。
[root@localhost ~]# ifconfig eth0 10.1.1.10 netmask 255.0.0.0
查看网卡接口信息,默认列出所有接口
[root@localhost ~]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:0C:29:13:5D:74
inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fe13:5d74/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:413 errors:0 dropped:0 overruns:0 frame:0
TX packets:572 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:47701 (46.5 KiB) TX bytes:64842 (63.3 KiB)
Base address:0x2000 Memory:d8920000-d8940000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:407 errors:0 dropped:0 overruns:0 frame:0
TX packets:407 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:70759 (69.1 KiB) TX bytes:70759 (69.1 KiB)
查看当前路由及网关信息
[root@localhost ~]# netstat -r
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
192.168.1.0 * 255.255.255.0 U 0 0 0 eth0
169.254.0.0 * 255.255.0.0 U 0 0 0 eth0
default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0DNS:主机名:CentOS主DNS:202.106.46.151
第二
DNS:202.106.0.20
第三
DNS:8.8.8.8网络配 置:
eth0静态ip:192.168.1.106
子网掩码 255.255.255.0
默认网关 IP 192.168.1.1
DEVICE=eth0
IPADDR=192.168.1.106
NETMASK=255.255.255.0
BROADCAST=192.168.1.255
ONBOOT=yes
BOOTPROTO=none
GATEWAY=192.168.1.1
TYPE=Ethernet
"/etc/sysconfig/network-scripts/ifcfg-eth0"
原文网址: http://www.cnblogs.com/vicowong/archive/2011/04/23/2025545.html