u-boot2020.04移植（3、lowlevel_init.S）

现在开始就进入板级相关的初始化了，跳转到board/samsung/goni/lowlevel_init.S文件，注意这里lowlevel_init搜索出来在arch/arm/cpu/armv7/lowlevel_init.S文件里面也有，而且这个文件还被编译了，但仔细看一下就会发现，这个文件里面的lowlevel_init被声明成了弱属性，所以真正调用的是board/samsung/goni/lowlevel_init.S文件。

ENTRY(cpu_init_crit)
	/*
	 * Jump to board specific initialization...
	 * The Mask ROM will have already initialized
	 * basic memory. Go here to bump up clock rate and handle
	 * wake up conditions.
	 */
	b	lowlevel_init		@ go setup pll,mux,memory
ENDPROC(cpu_init_crit)

其实在lowlevel_init里面也不需要干多少事，但DDR是必须要初始化好的，我们都知道s5pv210的整个IRAM也就96K，而u-boot的大小远远超过了96K，所以比较好的办法就是在BL1阶段就初始化好DDR，并且将u-boot搬运到DDR运行，但是BL1的大小最大只有16K，所以得尽早将DDR初始化好，然后到DDR中运行，这一步本来也是必须的，因为现在u-boot运行在IRAM内，其运行地址与链接地址是不一样的，只能运行位置无关代码。

下面看下lowlevel_init得源码：

board/samsung/goni/lowlevel_init.S

.globl lowlevel_init
lowlevel_init:
	/*这里将lr得值保存到r11中，以便之后返回，因为后面也有跳转得过程，防止lr跳转后丢失*/
	mov	r11, lr

	/* r5 has always zero */
	mov	r5, #0

	ldr	r7, =S5PC100_GPIO_BASE
	ldr	r8, =S5PC100_GPIO_BASE
	/* Read CPU ID */
	ldr	r2, =S5PC110_PRO_ID
	ldr	r0, [r2]
	mov	r1, #0x00010000
	and	r0, r0, r1
	/*根据手册可以得出，这里是不等的*/
	cmp	r0, r5
	beq	100f
	/*这里将r8重新赋值成了C110的GPIO基地址*/
	ldr	r8, =S5PC110_GPIO_BASE
100:
	/* Turn on KEY_LED_ON [GPJ4(1)] XMSMWEN */
	/*比较结果不相等，这里比较后，Z位的值是一直保持的*/
	cmp	r7, r8
	/*不相等，不执行*/
	beq	skip_check_didle			@ Support C110 only

    /*读取复位状态*/
	ldr	r0, =S5PC110_RST_STAT
	ldr	r1, [r0]
	and	r1, r1, #0x000D0000
	cmp	r1, #(0x1 << 19)			@ DEEPIDLE_WAKEUP
	/*如果是从DEEPIDLE模式唤醒的就直接跳到didle_wakeup过程*/
	beq	didle_wakeup
	cmp	r7, r8

skip_check_didle:
	/*下面这一堆代码就是点亮了一颗led灯，我们改成自己板子上对应的灯GPJ0_3*/
	addeq	r0, r8, #0x280				@ S5PC100_GPIO_J4
	addne	r0, r8, #0x240				@ S5PC110_GPIO_J0
	ldr	r1, [r0, #0x0]				@ GPIO_CON_OFFSET
	bic	r1, r1, #(0xf << 12)			@ 3 * 4-bit
	orr	r1, r1, #(0x1 << 12)
	str	r1, [r0, #0x0]				@ GPIO_CON_OFFSET

	ldr	r1, [r0, #0x4]				@ GPIO_DAT_OFFSET
	bic	r1, r1, #(1 << 3)
	str	r1, [r0, #0x4]				@ GPIO_DAT_OFFSET

	/*执行到这里，上面点的那颗led灯，如果亮了的话那就说明前面暂时没什么问题了*/
	/* Don't setup at s5pc100 */
	beq	100f

	/*下面这堆都是写的默认值，不知道具体的作用*/
	/*
	 省略
    */

	/*
	 * Diable ABB block to reduce sleep current at low temperature
	 * Note that it's hidden register setup don't modify it
	 */
	 /*这里操作的是隐藏寄存器，不要动*/
	ldr	r0, =0xE010C300
	ldr	r1, =0x00800000
	str	r1, [r0]

100:
	/* IO retension release */
	/*这一堆好像与低功耗有关*/
	ldreq	r0, =S5PC100_OTHERS			@ 0xE0108200
	ldrne	r0, =S5PC110_OTHERS			@ 0xE010E000
	ldr	r1, [r0]
	ldreq	r2, =(1 << 31)				@ IO_RET_REL
	ldrne	r2, =((1 << 31) | (1 << 30) | (1 << 29) | (1 << 28))
	orr	r1, r1, r2
	/* Do not release retention here for S5PC110 */
	streq	r1, [r0]

	/* Disable Watchdog */
	ldreq	r0, =S5PC100_WATCHDOG_BASE		@ 0xEA200000
	ldrne	r0, =S5PC110_WATCHDOG_BASE		@ 0xE2700000
	str	r5, [r0]

	/* setting SRAM */
	ldreq	r0, =S5PC100_SROMC_BASE
	ldrne	r0, =S5PC110_SROMC_BASE
	ldr	r1, =0x9
	str	r1, [r0]

	/* S5PC100 has 3 groups of interrupt sources */
	/*s5pv210有四组中断源，这里只失能了三组，再添加一组*/
	ldreq	r0, =S5PC100_VIC0_BASE			@ 0xE4000000
	ldrne	r0, =S5PC110_VIC0_BASE			@ 0xF2000000
	add	r1, r0, #0x00100000
	add	r2, r0, #0x00200000
	/*r4还没被用过，使用r4*/
	add	r4, r0, #0x00300000

	/* Disable all interrupts (VIC0, VIC1 and VIC2, VIC3) */
	mvn	r3, #0x0
	str	r3, [r0, #0x14]				@ INTENCLEAR
	str	r3, [r1, #0x14]				@ INTENCLEAR
	str	r3, [r2, #0x14]				@ INTENCLEAR
	/*增加VIC3*/
	str	r3, [r4, #0x14]				@ INTENCLEAR

	/* Set all interrupts as IRQ */
	str	r5, [r0, #0xc]				@ INTSELECT
	str	r5, [r1, #0xc]				@ INTSELECT
	str	r5, [r2, #0xc]				@ INTSELECT
	/*增加VIC3*/
	str	r5, [r4, #0xc]				@ INTSELECT

	/* Pending Interrupt Clear */
	str	r5, [r0, #0xf00]			@ INTADDRESS
	str	r5, [r1, #0xf00]			@ INTADDRESS
	str	r5, [r2, #0xf00]			@ INTADDRESS
	/*增加VIC3*/
	str	r5, [r4, #0xf00]			@ INTADDRESS

	/* for UART */
	/*由于IROM代码已经初始化了串口2，而在u-boot里面我也使用的串口2作为调试串口，
	所以可以选择不初始化,但是后面重新配置了时钟，IROM中的配置在新的时钟下工作不正常，没有输出，
	主要应该就是波特率相关寄存器的设置没法用了，所以再重新配置一下（参考后面的修改）*/
	bl	uart_asm_init

	bl	internal_ram_init

	cmp	r7, r8
	/* Clear wakeup status register */
	ldreq	r0, =S5PC100_WAKEUP_STAT
	ldrne	r0, =S5PC110_WAKEUP_STAT
	/*这里是不是感觉什么都没做，但实际上手册说的是写1清除该位，默认状态为0，
	那猜测有效状态应该是1，将读出来的值1又写回去就清除了该位*/
	ldr	r1, [r0]
	str	r1, [r0]

	/* IO retension release */
	/*是不是很熟悉，前面也有一段一模一样的代码，不知道意欲何为*/
	/*
    省略
    */

	/*向下找标号1*/
	b	1f

/*如果前面检测出是DEEPIDLE模式唤醒的，那么直接就到这儿了*/
didle_wakeup:
	/* Wait when APLL is locked */
	ldr	r0, =0xE0100100			@ S5PC110_APLL_CON
lockloop:
    /*等待APLL时钟稳定*/
	ldr	r1, [r0]
	and	r1, r1, #(1 << 29)
	cmp	r1, #(1 << 29)
	bne	lockloop

    /*S5PC110_INFORM0是一个用户自定义寄存器*/
	ldr	r0, =S5PC110_INFORM0
	ldr	r1, [r0]
    /*这里将r1的值放到pc指针里面了，猜测是某个地方进入DEEPIDLE的时候，
    将lr的值保存到了S5PC110_INFORM0里面，这里直接读出来后返回之前执行的地方*/
	mov	pc, r1
	nop
	nop
	nop
	nop
	nop

1:
	/*到了这里就直接返回了*/
	mov	lr, r11
	mov	pc, lr

从源码可以看出，目前lowlevel_init主要做的事：

检测唤醒条件
点了一颗灯显示当前运行到哪儿了
Initialize Async Register
IO retension release相关的
关看门狗
设置SRAM
关中断（这里中断和之前arm内核部分的中断不一样，这些中断是三星公司设计的）
初始化了四个串口的引脚
初始化内部RAM
清除唤醒状态
IO retension release相关的

目前CPU好像是运行在400MHz下的，在本文件lowlevel_init.S的末尾有一个时钟初始化的过程，但是没有被调用，将其添加上：

   /*添加到这句后面*/
bl	internal_ram_init

	/*初始化时钟*/
	bl system_clock_init

由于重新配置了时钟，而串口2的初始化使用的PCLK时钟没有使用串口专有的时钟，所以也跟着发生了变化，串口2在IROM中的配置已经不能用了，不能输出信息，重新配置一下：

/*
 * uart_asm_init: Initialize UART's pins
 */
uart_asm_init:
	/* set GPIO to enable UART0-UART4 */
	mov	r0, r8
	ldr	r1, =0x22222222
	str	r1, [r0, #0x0]			@ S5PC100_GPIO_A0_OFFSET
	ldr	r1, =0x00002222
	str	r1, [r0, #0x20]			@ S5PC100_GPIO_A1_OFFSET

	/* Check S5PC100 */
	cmp	r7, r8
	bne	110f

	/* UART_SEL GPK0[5] at S5PC100 */
	/*
    省略
    */

	b	200f
110:
	/*
	 * Note that the following address
	 * 0xE020'0360 is reserved address at S5PC100
	 */
	/* UART_SEL MP0_5[7] at S5PC110 */
	/*下面这堆代码是在设置MP05_7这个脚,但在我的开发板上悬空的，可以删除，也可以不管*/
	/*
    省略
    */

	/*配置串口2*/
	ldr r0, =S5PC110_UART_BASE
	/*ULCON 8n1*/
	ldr r1, =0x3
	str r1, [r0, #0x800]
	/*UCON*/
	ldr r1, =0x5
	str r1, [r0, #0x804]
	/*UFCON*/
	ldr r1, =0x217
	str r1, [r0, #0x808]
	/*UMCON*/
	ldr r1, =0x0
	str r1, [r0, #0x80C]
	/*UBRDIV*/
	ldr r1, =34
	str r1, [r0, #0x828]
	/*UDIVSLOT*/
	ldr r1, =0xDFDD
	str r1, [r0, #0x82C]
200:
	mov	pc, lr

接着是初始化DDR，我这个开发板的配置是4片128M，每两片并联组成32bit的数据线访问，总容量512M，从手册上面可以得知此芯片有两个DDR控制器，总共能扩展的DDR内存最大1.5G：

扫描二维码关注公众号，回复： 11479098 查看本文章

硬件上前256M在DRAM0区域，后256M在DRAM1区域，为了让两片地址连续起来，前256M的起始地址设置为0x30000000，后256M的起始地址设为0x40000000，这样刚好地址连续，DDR的初始化程序参考三星提供的，下面只对配置部分参数进行说明，关于时间参数不进行讲解，配置流程参见手册DRAM CONTROLLER篇（完整初始化代码见本文末尾）：

/*chip相当于rank，就好像电脑的内存插槽是有正反两面的，我们只有一面，也就是一个rank*/
#define DMC0_MEMCONTROL		0x00202400 	// MemControl	BL=4, 1Chip, DDR2 Type, dynamic self refresh, force precharge, dynamic power down off

/*30代表起始地址是0x30000000，F0有点像大小的意思代表0xfffffff，1有点像扫描方式，3列的位数是10，2行的位数是14，3bank数是8*/
#define DMC0_MEMCONFIG_0	0x30F01323	// MemConfig0	256MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixed
/*前面说了我们只用了一面，另一面没用*/
#define DMC0_MEMCONFIG_1	0x30F00312	// MemConfig1		默认值

#define DMC0_TIMINGA_REF	0x00000618	// TimingAref	7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4E)
#define DMC0_TIMING_ROW		0x28233287	// TimingRow	for @200MHz
#define DMC0_TIMING_DATA	0x23240304	// TimingData	CL=3
#define	DMC0_TIMING_PWR		0x09C80232	// TimingPower

#define	DMC1_MEMCONTROL		0x00202400	// MemControl	BL=4, 1chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down off

/*除了起始地址，其它描述和DMC0都一样*/
#define DMC1_MEMCONFIG_0	0x40F01323	// MemConfig0	256MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixed
/*这个也是只用了一面*/
#define DMC1_MEMCONFIG_1	0x60E00312	// MemConfig1		默认值

#define DMC1_TIMINGA_REF	0x00000618	// TimingAref	7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4
#define DMC1_TIMING_ROW		0x28233289	// TimingRow	for @200MHz
#define DMC1_TIMING_DATA	0x23240304	// TimingData	CL=3
#define	DMC1_TIMING_PWR		0x08280232	// TimingPower

将DDR初始化程序，ddr_init.S文件放到board/samsung/goni/目录，然后修改该目录下的Makefile,添加ddr_init.S的编译：

obj-y	:= goni.o onenand.o
obj-y	+= lowlevel_init.o
/*增加ddr_init*/
obj-y	+= ddr_init.o

然后在时钟初始化的后面添加上DDR的初始化：

/*...*/
bl	internal_ram_init

	/*初始化时钟*/
	bl system_clock_init

	/*初始化DDR*/
	bl sdram_asm_init

DDR怎么验证有没有初始化成功呢，可以添加一段测试程序，先向DDR的某个地址（注意这个地址一定要四字节对齐，因为前面开启了对齐检查，否则访问非对齐地址时会出错，而且这个错误的唯一现象就是你看不到任何输出，这时你可能会怀疑你的DDR初始化没有成功，导致写DDR时出错，但实际上是因为访问了非对齐地址）写入几个值，然后再读出来，我这里写了OK两个字符，通过串口打印查看就可以了：

/*写入字符'O'*/
	ldr r0, =0x40000000
	ldr r1, =0x4f
	str r1, [r0]
	/*写入字符'K'*/
	ldr r0, =0x40000004
	ldr r1, =0x4b
	str r1, [r0]
	/*读出然后通过串口输出*/
	ldr r0, =0xE2900820
	ldr r1, =0x40000000
	ldr r2, [r1]
	str r2, [r0]
	/*读出然后通过串口输出*/
	ldr r0, =0xE2900820
	ldr r1, =0x40000004
	ldr r2, [r1]
	str r2, [r0]

由于硬件设计的原因，开发板上电后还需要进行电源置锁，不然的话开机按钮如果松手的话就掉电了，这里将电源置锁加上：

/*这个只是简单的拉了一个IO的电平，不作介绍，添加函数体的实现到lowlevel_init.S文件的末尾，然后在时钟初始化的前面调用*/
board_power_hold:
	ldr r0, =0xE010E81C
	ldr r1, [r0]
	ldr r2, =((0x1 << 0) | (0x1 << 8) | (0x1 << 9))
	orr r1, r1, r2
	str r1, [r0]
	mov pc, lr

在时钟初始化前调用：

/*...*/
bl	internal_ram_init

	/*电源置锁*/
	bl board_power_hold

	/*初始化时钟*/
	bl system_clock_init

	/*初始化DDR*/
	bl sdram_asm_init

到了这里，DDR已经初始化好了，下一步就是将u-boot拷贝到DDR去执行了，我们u-boot是烧写到sd卡的，三星在IROM代码中已经提供了将SD卡的内容拷贝到内存的函数实现，我们只需要调用就可以了，这里参考手册（S5PV210_iROM_ApplicationNote_Preliminary_20091126.pdf）：

图2

上面图2表示这个地址存储了当前的启动通道地址，图3就是拷贝函数，三星提供了好几个这样的拷贝函数，用于从不同启动介质中拷贝内容到内存中，这里只截取了SD/MMC和eMMC的拷贝函数，从上面的图可以看出CopySDMMCtoMem这个函数的函数体就放在0xD0037F98这个地址，所以我们只需要通过函数指针的方式，访问这个地址的内容就相当于调用这个函数了，在board/samsung/goni/目录添加一个copy_image_to_mem.c文件，写入以下代码：

#include <configs/s5p_goni.h>

/*
参数1：通道号
参数2：从SD卡的哪个扇区开始拷贝
参数3：拷贝多少个扇区
参数4：拷贝到内存的哪里
参数5：不知道具体用途
*/
typedef bool (*CopySDMMCtoMemTypeDef)(int, unsigned int, unsigned short, unsigned int*, bool);

void CopySDMMCtoMem(void)
{
    CopySDMMCtoMemTypeDef pFuncCopySDMMCtoMem;

    pFuncCopySDMMCtoMem = (CopySDMMCtoMemTypeDef)(*((volatile unsigned int *)0xD0037F98));
    unsigned int ch = *((volatile unsigned int*)(0xd0037488));

    if(ch == 0xeb000000)
    {
        /*通道0，iNand*/
    }
    else if(ch == 0xeb200000)
    {
        /*通道2，SD卡*/
        pFuncCopySDMMCtoMem(2, 45, 1000,(unsigned int*)CONFIG_SYS_TEXT_BASE, 0); 
    }
}

有个需要注意的地方就是拷贝到内存的地址，这是个C函数，函数的调用需要使用栈，前面start.S里面设置过一次栈，这里的内存地址最好不要和当时设置的栈空间冲突（注意栈的生长方向是向下的）；然后就是SD卡的起始扇区，这个是和你烧写u-boot的起始扇区一样的，因为我是烧写到45扇区开始的位置（这个位置不是固定的，只要没有覆盖掉BL1就行了），所以这里设置45，拷贝大小（这里设置的参数值是扇区数，乘以扇区大小512才是真正的大小，我这里拷贝1000*512=500K）只要大于等于u-boot的大小就行了，然后内存地址我设置的是链接地址。

顺便贴下我的烧写脚本：

#! /bin/bash

UBOOT=2020.04

#mkv210_image是制作BL1的，因为BL1前16个字节需要填写头信息
./mkv210_image ~/Desktop/s5pv210/u-boot-${UBOOT}/u-boot.bin u-boot-sd.bin
sudo dd iflag=dsync oflag=dsync if=u-boot-sd.bin of=/dev/sdb seek=1
sudo dd iflag=dsync oflag=dsync if=~/Desktop/s5pv210/u-boot-${UBOOT}/u-boot.bin of=/dev/sdb seek=45

在board/samsung/goni/Makefile中添加，让其编译进u-boot，就可以调用这个函数进行拷贝了：

obj-y	:= goni.o onenand.o
obj-y	+= lowlevel_init.o
obj-y	+= ddr_init.o
/*添加编译*/
obj-y	+= copy_image_to_mem.o

/*...*/
bl	internal_ram_init

	/*电源置锁*/
	bl board_power_hold

	/*初始化时钟*/
	bl system_clock_init

	/*初始化DDR*/
	bl sdram_asm_init

	/*拷贝u-boot到DDR*/
	bl CopySDMMCtoMem

其实还有很重要的一步，我前面没有提到，就是我们调用的这个函数是不是都在BL1里面，也就是是不是在u-boot的前16K，我们可以通过查看System.map文件，这个文件是u-boot编译后生成的，位于u-boot根目录：

起始地址可以看到是0x34800000，前16K的内容就截止与0x34804000这个地址，所以我们只需要看我们调用的内容有没有在这个地址内就行了，或者可以反汇编u-boot文件也可以知道，相对来说反汇编u-boot文件要详细点。

好的，u-boot已经拷贝到DDR里面了，所以紧接着我们进入DDR的u-boot中去执行，修改arch/arm/cpu/armv7/start.S文件：

#ifndef CONFIG_SKIP_LOWLEVEL_INIT
#ifdef CONFIG_CPU_V7A
	bl	cpu_init_cp15
#endif
#ifndef CONFIG_SKIP_LOWLEVEL_INIT_ONLY
	bl	cpu_init_crit
#endif
#endif

    /*注释掉*/
	@ bl	_main
	/*修改这里，跳转到DDR中去执行*/
	ldr pc, =_main

这部分内容结束，就进入board_init_f了（也就是大家说的u-boot的第一阶段），所以编译看一下效果：

可以看到已经出来很多信息了，说明我们成功跳转到DDR去执行了，不过卡在了OneNAND初始化的后面。

完整DDR初始化代码：

#include <config.h>

#define ELFIN_GPIO_BASE   S5PC110_GPIO_BASE
 
#define MP1_0DRV_SR_OFFSET 		0x3CC
#define MP1_1DRV_SR_OFFSET 		0x3EC
#define MP1_2DRV_SR_OFFSET 		0x40C
#define MP1_3DRV_SR_OFFSET 		0x42C
#define MP1_4DRV_SR_OFFSET 		0x44C
#define MP1_5DRV_SR_OFFSET 		0x46C
#define MP1_6DRV_SR_OFFSET 		0x48C
#define MP1_7DRV_SR_OFFSET 		0x4AC
#define MP1_8DRV_SR_OFFSET 		0x4CC
 
#define MP2_0DRV_SR_OFFSET 		0x4EC
#define MP2_1DRV_SR_OFFSET 		0x50C
#define MP2_2DRV_SR_OFFSET 		0x52C
#define MP2_3DRV_SR_OFFSET 		0x54C
#define MP2_4DRV_SR_OFFSET 		0x56C
#define MP2_5DRV_SR_OFFSET 		0x58C
#define MP2_6DRV_SR_OFFSET 		0x5AC
#define MP2_7DRV_SR_OFFSET 		0x5CC
#define MP2_8DRV_SR_OFFSET 		0x5EC

/*
 * SDRAM Controller
 */
#define APB_DMC_0_BASE			0xF0000000
#define APB_DMC_1_BASE			0xF1400000
#define ASYNC_MSYS_DMC0_BASE	0xF1E00000
 
#define DMC_CONCONTROL 			0x00
#define DMC_MEMCONTROL 			0x04
#define DMC_MEMCONFIG0 			0x08
#define DMC_MEMCONFIG1 			0x0C
#define DMC_DIRECTCMD 			0x10
#define DMC_PRECHCONFIG 		0x14
#define DMC_PHYCONTROL0 		0x18
#define DMC_PHYCONTROL1 		0x1C
#define DMC_RESERVED 			0x20
#define DMC_PWRDNCONFIG 		0x28
#define DMC_TIMINGAREF 			0x30
#define DMC_TIMINGROW 			0x34
#define DMC_TIMINGDATA 			0x38
#define DMC_TIMINGPOWER 		0x3C
#define DMC_PHYSTATUS 			0x40
#define DMC_CHIP0STATUS 		0x48
#define DMC_CHIP1STATUS 		0x4C
#define DMC_AREFSTATUS 			0x50
#define DMC_MRSTATUS 			0x54
#define DMC_PHYTEST0 			0x58
#define DMC_PHYTEST1 			0x5C
#define DMC_QOSCONTROL0 		0x60
#define DMC_QOSCONFIG0 			0x64
#define DMC_QOSCONTROL1 		0x68
#define DMC_QOSCONFIG1 			0x6C
#define DMC_QOSCONTROL2 		0x70
#define DMC_QOSCONFIG2 			0x74
#define DMC_QOSCONTROL3 		0x78
#define DMC_QOSCONFIG3 			0x7C
#define DMC_QOSCONTROL4 		0x80
#define DMC_QOSCONFIG4 			0x84
#define DMC_QOSCONTROL5 		0x88
#define DMC_QOSCONFIG5 			0x8C
#define DMC_QOSCONTROL6 		0x90
#define DMC_QOSCONFIG6 			0x94
#define DMC_QOSCONTROL7 		0x98
#define DMC_QOSCONFIG7 			0x9C
#define DMC_QOSCONTROL8 		0xA0
#define DMC_QOSCONFIG8 			0xA4
#define DMC_QOSCONTROL9 		0xA8
#define DMC_QOSCONFIG9 			0xAC
#define DMC_QOSCONTROL10 		0xB0
#define DMC_QOSCONFIG10 		0xB4
#define DMC_QOSCONTROL11 		0xB8
#define DMC_QOSCONFIG11 		0xBC
#define DMC_QOSCONTROL12 		0xC0
#define DMC_QOSCONFIG12 		0xC4
#define DMC_QOSCONTROL13 		0xC8
#define DMC_QOSCONFIG13 		0xCC
#define DMC_QOSCONTROL14 		0xD0
#define DMC_QOSCONFIG14 		0xD4
#define DMC_QOSCONTROL15 		0xD8
#define DMC_QOSCONFIG15 		0xDC

#define DMC0_MEMCONTROL		0x00202400 	// MemControl	BL=4, 1Chip, DDR2 Type, dynamic self refresh, force precharge, dynamic power down off

#define DMC0_MEMCONFIG_0	0x30F01323	// MemConfig0	256MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixed
#define DMC0_MEMCONFIG_1	0x30F00312	// MemConfig1		默认值

#define DMC0_TIMINGA_REF	0x00000618	// TimingAref	7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4E)
#define DMC0_TIMING_ROW		0x28233287	// TimingRow	for @200MHz
#define DMC0_TIMING_DATA	0x23240304	// TimingData	CL=3
#define	DMC0_TIMING_PWR		0x09C80232	// TimingPower

#define	DMC1_MEMCONTROL		0x00202400	// MemControl	BL=4, 1chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down off

#define DMC1_MEMCONFIG_0	0x40F01323	// MemConfig0	256MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixed
#define DMC1_MEMCONFIG_1	0x60E00312	// MemConfig1		默认值

#define DMC1_TIMINGA_REF	0x00000618	// TimingAref	7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4
#define DMC1_TIMING_ROW		0x28233289	// TimingRow	for @200MHz
#define DMC1_TIMING_DATA	0x23240304	// TimingData	CL=3
#define	DMC1_TIMING_PWR		0x08280232	// TimingPower

.globl sdram_asm_init
sdram_asm_init:	
	ldr	r0, =0xf1e00000
	ldr	r1, =0x0
	str	r1, [r0, #0x0]

	/* DMC0 Drive Strength (Setting 2X) */
	
	ldr	r0, =ELFIN_GPIO_BASE

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP1_0DRV_SR_OFFSET]		// 寄存器中对应0b10，就是2X

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP1_1DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP1_2DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP1_3DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP1_4DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP1_5DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP1_6DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP1_7DRV_SR_OFFSET]

	ldr	r1, =0x00002AAA
	str	r1, [r0, #MP1_8DRV_SR_OFFSET]

	
	/* DMC1 Drive Strength (Setting 2X) */
	
	ldr	r0, =ELFIN_GPIO_BASE
	
	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP2_0DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP2_1DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP2_2DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP2_3DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP2_4DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP2_5DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP2_6DRV_SR_OFFSET]

	ldr	r1, =0x0000AAAA
	str	r1, [r0, #MP2_7DRV_SR_OFFSET]

	ldr	r1, =0x00002AAA
	str	r1, [r0, #MP2_8DRV_SR_OFFSET]
	
	/* DMC0 initialization at single Type*/
	ldr	r0, =APB_DMC_0_BASE

	ldr	r1, =0x00101000				@PhyControl0 DLL parameter setting, manual 0x00101000
	str	r1, [r0, #DMC_PHYCONTROL0]

	ldr	r1, =0x00000086				@PhyControl1 DLL parameter setting, LPDDR/LPDDR2 Case
	str	r1, [r0, #DMC_PHYCONTROL1]

	ldr	r1, =0x00101002				@PhyControl0 DLL on
	str	r1, [r0, #DMC_PHYCONTROL0]

	ldr	r1, =0x00101003				@PhyControl0 DLL start
	str	r1, [r0, #DMC_PHYCONTROL0]

find_lock_val:
	ldr	r1, [r0, #DMC_PHYSTATUS]		@Load Phystatus register value
	and	r2, r1, #0x7
	cmp	r2, #0x7				@Loop until DLL is locked
	bne	find_lock_val
	
	and	r1, #0x3fc0 
	mov	r2, r1, LSL #18
	orr	r2, r2, #0x100000
	orr	r2 ,r2, #0x1000	
		
	orr	r1, r2, #0x3				@Force Value locking
	str	r1, [r0, #DMC_PHYCONTROL0]
	
#if 0	/* Memory margin test 10.01.05 */
	orr	r1, r2, #0x1				@DLL off
	str	r1, [r0, #DMC_PHYCONTROL0]
#endif
	/* setting DDR2 */
	ldr	r1, =0x0FFF2010				@ConControl auto refresh off
	str	r1, [r0, #DMC_CONCONTROL]

	ldr	r1, =DMC0_MEMCONTROL			@MemControl BL=4, 1 chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down off
	str	r1, [r0, #DMC_MEMCONTROL]
	
	ldr	r1, =DMC0_MEMCONFIG_0			@MemConfig0 256MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixed
	str	r1, [r0, #DMC_MEMCONFIG0]

	ldr	r1, =DMC0_MEMCONFIG_1			@MemConfig1
	str	r1, [r0, #DMC_MEMCONFIG1]

	ldr	r1, =0xFF000000				@PrechConfig
	str	r1, [r0, #DMC_PRECHCONFIG]
	
	ldr	r1, =DMC0_TIMINGA_REF			@TimingAref	7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4E)
	str	r1, [r0, #DMC_TIMINGAREF]
	
	ldr	r1, =DMC0_TIMING_ROW			@TimingRow	for @200MHz
	str	r1, [r0, #DMC_TIMINGROW]

	ldr	r1, =DMC0_TIMING_DATA			@TimingData	CL=3
	str	r1, [r0, #DMC_TIMINGDATA]
	
	ldr	r1, =DMC0_TIMING_PWR			@TimingPower
	str	r1, [r0, #DMC_TIMINGPOWER]

	ldr	r1, =0x07000000				@DirectCmd	chip0 Deselect
	str	r1, [r0, #DMC_DIRECTCMD]
	
	ldr	r1, =0x01000000				@DirectCmd	chip0 PALL
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00020000				@DirectCmd	chip0 EMRS2
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00030000				@DirectCmd	chip0 EMRS3
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00010400				@DirectCmd	chip0 EMRS1 (MEM DLL on, DQS# disable)
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00000542				@DirectCmd	chip0 MRS (MEM DLL reset) CL=4, BL=4
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x01000000				@DirectCmd	chip0 PALL
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x05000000				@DirectCmd	chip0 REFA
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x05000000				@DirectCmd	chip0 REFA
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00000442				@DirectCmd	chip0 MRS (MEM DLL unreset)
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00010780				@DirectCmd	chip0 EMRS1 (OCD default)
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00010400				@DirectCmd	chip0 EMRS1 (OCD exit)
	str	r1, [r0, #DMC_DIRECTCMD]
	
	ldr	r1, =0x07100000				@DirectCmd	chip1 Deselect
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x01100000				@DirectCmd	chip1 PALL
	str	r1, [r0, #DMC_DIRECTCMD]
	
	ldr	r1, =0x00120000				@DirectCmd	chip1 EMRS2
	str	r1, [r0, #DMC_DIRECTCMD]
	
	ldr	r1, =0x00130000				@DirectCmd	chip1 EMRS3
	str	r1, [r0, #DMC_DIRECTCMD]
	
	ldr	r1, =0x00110400				@DirectCmd	chip1 EMRS1 (MEM DLL on, DQS# disable)
	str	r1, [r0, #DMC_DIRECTCMD]
	
	ldr	r1, =0x00100542				@DirectCmd	chip1 MRS (MEM DLL reset) CL=4, BL=4
	str	r1, [r0, #DMC_DIRECTCMD]
	
	ldr	r1, =0x01100000				@DirectCmd	chip1 PALL
	str	r1, [r0, #DMC_DIRECTCMD]
	
	ldr	r1, =0x05100000				@DirectCmd	chip1 REFA
	str	r1, [r0, #DMC_DIRECTCMD]
	
	ldr	r1, =0x05100000				@DirectCmd	chip1 REFA
	str	r1, [r0, #DMC_DIRECTCMD]
	
	ldr	r1, =0x00100442				@DirectCmd	chip1 MRS (MEM DLL unreset)
	str	r1, [r0, #DMC_DIRECTCMD]
	
	ldr	r1, =0x00110780				@DirectCmd	chip1 EMRS1 (OCD default)
	str	r1, [r0, #DMC_DIRECTCMD]
		
	ldr	r1, =0x00110400				@DirectCmd	chip1 EMRS1 (OCD exit)
	str	r1, [r0, #DMC_DIRECTCMD]
		
	ldr	r1, =0x0FF02030				@ConControl	auto refresh on
	str	r1, [r0, #DMC_CONCONTROL]
		
	ldr	r1, =0xFFFF00FF				@PwrdnConfig
	str	r1, [r0, #DMC_PWRDNCONFIG]
		
	ldr	r1, =0x00202400				@MemControl	BL=4, 2 chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down off
	str	r1, [r0, #DMC_MEMCONTROL]
	
// 上面是DRAM0初始化步骤
/*******************************************************************************************/	
// 下面是DRAM1初始化步骤，两者没有联系，是并列的。

	/* DMC1 initialization */
	ldr	r0, =APB_DMC_1_BASE
	ldr	r1, =0x00101000				@Phycontrol0 DLL parameter setting
	str	r1, [r0, #DMC_PHYCONTROL0]

	
	ldr	r1, =0x00000086				@Phycontrol1 DLL parameter setting
	str	r1, [r0, #DMC_PHYCONTROL1]
	ldr	r1, =0x00101002				@PhyControl0 DLL on
	str	r1, [r0, #DMC_PHYCONTROL0]
	ldr	r1, =0x00101003				@PhyControl0 DLL start
	str	r1, [r0, #DMC_PHYCONTROL0]
	
	
	
find_lock_val1:
	ldr	r1, [r0, #DMC_PHYSTATUS]		@Load Phystatus register value
	and	r2, r1, #0x7
	cmp	r2, #0x7				@Loop until DLL is locked
	bne	find_lock_val1
	
	and	r1, #0x3fc0 
	mov	r2, r1, LSL #18
	orr	r2, r2, #0x100000
	orr	r2, r2, #0x1000
		
	orr	r1, r2, #0x3				@Force Value locking
	str	r1, [r0, #DMC_PHYCONTROL0]
	
#if 0	/* Memory margin test 10.01.05 */
	orr	r1, r2, #0x1				@DLL off
	str	r1, [r0, #DMC_PHYCONTROL0]
#endif

	/* settinf fot DDR2 */
	ldr	r0, =APB_DMC_1_BASE

	ldr	r1, =0x0FFF2010				@auto refresh off
	str	r1, [r0, #DMC_CONCONTROL]

	ldr	r1, =DMC1_MEMCONTROL			@MemControl	BL=4, 2 chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down off
	str	r1, [r0, #DMC_MEMCONTROL]

	ldr	r1, =DMC1_MEMCONFIG_0			@MemConfig0	512MB config, 8 banks,Mapping Method[12:15]0:linear, 1:linterleaved, 2:Mixed
	str	r1, [r0, #DMC_MEMCONFIG0]

	ldr	r1, =DMC1_MEMCONFIG_1			@MemConfig1
	str	r1, [r0, #DMC_MEMCONFIG1]

	ldr	r1, =0xFF000000
	str	r1, [r0, #DMC_PRECHCONFIG]

	ldr	r1, =DMC1_TIMINGA_REF			@TimingAref	7.8us*133MHz=1038(0x40E), 100MHz=780(0x30C), 20MHz=156(0x9C), 10MHz=78(0x4
	str	r1, [r0, #DMC_TIMINGAREF]

	ldr	r1, =DMC1_TIMING_ROW			@TimingRow	for @200MHz
	str	r1, [r0, #DMC_TIMINGROW]

	ldr	r1, =DMC1_TIMING_DATA			@TimingData	CL=3
	str	r1, [r0, #DMC_TIMINGDATA]

	ldr	r1, =DMC1_TIMING_PWR			@TimingPower
	str	r1, [r0, #DMC_TIMINGPOWER]


	ldr	r1, =0x07000000				@DirectCmd	chip0 Deselect
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x01000000				@DirectCmd	chip0 PALL
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00020000				@DirectCmd	chip0 EMRS2
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00030000				@DirectCmd	chip0 EMRS3
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00010400				@DirectCmd	chip0 EMRS1 (MEM DLL on, DQS# disable)
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00000542				@DirectCmd	chip0 MRS (MEM DLL reset) CL=4, BL=4
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x01000000				@DirectCmd	chip0 PALL
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x05000000				@DirectCmd	chip0 REFA
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x05000000				@DirectCmd	chip0 REFA
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00000442				@DirectCmd	chip0 MRS (MEM DLL unreset)
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00010780				@DirectCmd	chip0 EMRS1 (OCD default)
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00010400				@DirectCmd	chip0 EMRS1 (OCD exit)
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x07100000				@DirectCmd	chip1 Deselect
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x01100000				@DirectCmd	chip1 PALL
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00120000				@DirectCmd	chip1 EMRS2
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00130000				@DirectCmd	chip1 EMRS3
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00110440				@DirectCmd	chip1 EMRS1 (MEM DLL on, DQS# disable)
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00100542				@DirectCmd	chip1 MRS (MEM DLL reset) CL=4, BL=4
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x01100000				@DirectCmd	chip1 PALL
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x05100000				@DirectCmd	chip1 REFA
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x05100000				@DirectCmd	chip1 REFA
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00100442				@DirectCmd	chip1 MRS (MEM DLL unreset)
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00110780				@DirectCmd	chip1 EMRS1 (OCD default)
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x00110400				@DirectCmd	chip1 EMRS1 (OCD exit)
	str	r1, [r0, #DMC_DIRECTCMD]

	ldr	r1, =0x0FF02030				@ConControl	auto refresh on
	str	r1, [r0, #DMC_CONCONTROL]

	ldr	r1, =0xFFFF00FF				@PwrdnConfig	
	str	r1, [r0, #DMC_PWRDNCONFIG]

	ldr	r1, =DMC1_MEMCONTROL			@MemControl	BL=4, 2 chip, DDR2 type, dynamic self refresh, force precharge, dynamic power down off
	str	r1, [r0, #DMC_MEMCONTROL]
	// 函数返回
	mov pc, lr

u-boot2020.04移植（3、lowlevel_init.S）

欢迎扫码关注我的微信公众号

猜你喜欢