H3C版本 HCL_V2.1.0_Setup
VirtualBox版本 VirtualBox-4.2.4-81684-Win
（版本需匹配才可以正常使用H3C）
一、实验目的
1.了解静态路由的实验原理
2.掌握静态路由的配置
二、实验原理
- 静态路由定义
要想实现全网通信，也就是网络中的任意两个节点都能通信，这就要求每个路由器的路由表中必须有到所有网段的路由。对于路由器来说，它只知道自己直连的网段，对于没有直连的网段，需要管理员人工添加到这些网段的路由。管理员人工添加到某个网段如何转发，就是静态路由。 - 静态路由配置
要想实现全网络通信，必须添加路由条目。
AR1路由器直连A、B两个网段，C、D网段没有直连，则需要添加到C、D网段的路由。
ip route-static 到达的目标网络号 子网掩码 下一跳的路由器接口地址
ip route-static 172.16.1.0 24 172.16.0.2
三、实验拓扑图
| 路由器 | 端口 | 端口ip |
|---|---|---|
| RTA | G0/0 | 192.168.1.1/24 |
| G0/1 | 192.168.2.1/24 | |
| RTB | G0/0 | 192.168.2.2/24 |
| G0/1 | 192.168.3.1/24 | |
| RTC | G0/0 | 192.168.3.2/24 |
| G0/1 | 192.168.4.1/24 | |
| SWA | G1/0/1 | 192.168.4.2/24 |
| G1/0/2 | 192.168.5.1/24 |
RTA路由器配置
[H3C]int g0/0
[H3C-GigabitEthernet0/0]ip address 192.168.1.1 24
[H3C-GigabitEthernet0/0]int g0/1
[H3C-GigabitEthernet0/1]ip address 192.168.2.1 24
[H3C-GigabitEthernet0/1]quit
[H3C]ip route-static 192.168.3.0 24 192.168.2.2
[H3C]ip route-static 192.168.4.0 24 192.168.2.2
[H3C]ip route-static 192.168.5.0 24 192.168.2.2
[H3C]display ip routing-table
Destinations : 19 Routes : 19
Destination/Mask Proto Pre Cost NextHop Interface
……
192.168.1.0/24 Direct 0 0 192.168.1.1 GE0/0
192.168.1.0/32 Direct 0 0 192.168.1.1 GE0/0
192.168.1.1/32 Direct 0 0 127.0.0.1 InLoop0
192.168.1.255/32 Direct 0 0 192.168.1.1 GE0/0
192.168.2.0/24 Direct 0 0 192.168.2.1 GE0/1
192.168.2.0/32 Direct 0 0 192.168.2.1 GE0/1
192.168.2.1/32 Direct 0 0 127.0.0.1 InLoop0
192.168.2.255/32 Direct 0 0 192.168.2.1 GE0/1
192.168.3.0/24 Static 60 0 192.168.2.2 GE0/1
192.168.4.0/24 Static 60 0 192.168.2.2 GE0/1
192.168.5.0/24 Static 60 0 192.168.2.2 GE0/1
……
RTB路由器配置
[H3C]int g0/0
[H3C-GigabitEthernet0/0]ip address 192.168.2.2 24
[H3C-GigabitEthernet0/0]int g0/1
[H3C-GigabitEthernet0/1]ip address 192.168.3.1 24
[H3C-GigabitEthernet0/1]quit
[H3C]ip route-static 192.168.4.0 24 192.168.3.2
[H3C]ip route-static 192.168.5.0 24 192.168.3.2
[H3C]ip route-static 192.168.1.0 24 192.168.2.1
[H3C]display ip routing-table
Destinations : 19 Routes : 19
Destination/Mask Proto Pre Cost NextHop Interface
……
192.168.1.0/24 Static 60 0 192.168.2.1 GE0/0
192.168.2.0/24 Direct 0 0 192.168.2.2 GE0/0
192.168.2.0/32 Direct 0 0 192.168.2.2 GE0/0
192.168.2.2/32 Direct 0 0 127.0.0.1 InLoop0
192.168.2.255/32 Direct 0 0 192.168.2.2 GE0/0
192.168.3.0/24 Direct 0 0 192.168.3.1 GE0/1
192.168.3.0/32 Direct 0 0 192.168.3.1 GE0/1
192.168.3.1/32 Direct 0 0 127.0.0.1 InLoop0
192.168.3.255/32 Direct 0 0 192.168.3.1 GE0/1
192.168.4.0/24 Static 60 0 192.168.3.2 GE0/1
192.168.5.0/24 Static 60 0 192.168.3.2 GE0/1
……
RTC路由器配置
[H3C]int g0/0
[H3C-GigabitEthernet0/0]ip address 192.168.3.2 24
[H3C-GigabitEthernet0/0]int g0/1
[H3C-GigabitEthernet0/1]ip address 192.168.4.1 24
[H3C-GigabitEthernet0/1]quit
[H3C]ip route-static 192.168.1.0 24 192.168.3.1
[H3C]ip route-static 192.168.2.0 24 192.168.3.1
[H3C]ip route-static 192.168.5.0 24 192.168.4.3
[H3C]display ip routing-table
Destinations : 19 Routes : 20
Destination/Mask Proto Pre Cost NextHop Interface
……
192.168.1.0/24 Static 60 0 192.168.3.1 GE0/0
192.168.2.0/24 Static 60 0 192.168.3.1 GE0/0
192.168.3.0/24 Direct 0 0 192.168.3.2 GE0/0
192.168.3.0/32 Direct 0 0 192.168.3.2 GE0/0
192.168.3.2/32 Direct 0 0 127.0.0.1 InLoop0
192.168.3.255/32 Direct 0 0 192.168.3.2 GE0/0
192.168.4.0/24 Direct 0 0 192.168.4.1 GE0/1
192.168.4.0/32 Direct 0 0 192.168.4.1 GE0/1
192.168.4.1/32 Direct 0 0 127.0.0.1 InLoop0
192.168.4.255/32 Direct 0 0 192.168.4.1 GE0/1
192.168.5.0/24 Static 60 0 192.168.4.2 GE0/1
……
SWA路由器配置
[H3C]vlan 10
[H3C-vlan10]port g1/0/1
[H3C-vlan10]int vlan 10
[H3C-Vlan-interface10]ip address 192.168.4.2 24
[H3C-Vlan-interface10]vlan 20
[H3C-vlan20]port g1/0/2
[H3C-Vlan-interface20]ip address 192.168.5.1 24
[H3C-Vlan-interface20]quit
[H3C]ip route-static 192.168.1.0 24 192.168.4.1
[H3C]ip route-static 192.168.2.0 24 192.168.4.1
[H3C]ip route-static 192.168.3.0 24 192.168.4.1
[H3C]int g1/0/1
[H3C-GigabitEthernet1/0/1]port link-type access
[H3C-GigabitEthernet1/0/1]port access vlan 10
[H3C-GigabitEthernet1/0/1]int g1/0/2
[H3C-GigabitEthernet1/0/2]port link-type access
[H3C-GigabitEthernet1/0/2]port access vlan 20
[H3C-GigabitEthernet1/0/2]dis cu int g1/0/1
#
interface GigabitEthernet1/0/1
port link-mode bridge
port access vlan 10
combo enable fiber
#
return
[H3C-GigabitEthernet1/0/2]dis cu int g1/0/2
#
interface GigabitEthernet1/0/2
port link-mode bridge
port access vlan 20
combo enable fiber
#
return
| PC | ip |
|---|---|
| PC1 | 192.168.1.88 |
| PC2 | 192.168.5.88 |
<H3C>ping 192.168.5.88
Ping 192.168.5.88 (192.168.5.88): 56 data bytes, press CTRL_C to break
56 bytes from 192.168.5.88: icmp_seq=0 ttl=251 time=12.000 ms
56 bytes from 192.168.5.88: icmp_seq=1 ttl=251 time=8.000 ms
56 bytes from 192.168.5.88: icmp_seq=2 ttl=251 time=7.000 ms
56 bytes from 192.168.5.88: icmp_seq=3 ttl=251 time=6.000 ms
56 bytes from 192.168.5.88: icmp_seq=4 ttl=251 time=7.000 ms
<H3C>ping 192.168.1.88
Ping 192.168.1.88 (192.168.1.88): 56 data bytes, press CTRL_C to break
56 bytes from 192.168.1.88: icmp_seq=0 ttl=251 time=8.000 ms
56 bytes from 192.168.1.88: icmp_seq=1 ttl=251 time=5.000 ms
56 bytes from 192.168.1.88: icmp_seq=2 ttl=251 time=8.000 ms
56 bytes from 192.168.1.88: icmp_seq=3 ttl=251 time=8.000 ms
56 bytes from 192.168.1.88: icmp_seq=4 ttl=251 time=8.000 ms
- 路由器只关心到某个网段如何转发数据包，因此在路由器上添加路由，必须是到某个网段（子网）的路由，不能添加到某个特定地址的路由。添加到一个IP地址的路由，主机位会自动归零。
- 路由器点到点链路的另一种路条目写法
ip route-static 到达的目标网络号 子网掩码 下一跳的路由器接口
ip route-static 172.16.1.0 24 E0/0 - H3C路由器相关操作命令
1）显示全部路由display ip routing-table
2）只显示静态路由display ip routing-table protocol static
3）删除静态路由no ip route-static 172.16.1.0 24 172.16.0.2
undo ip route-static 172.16.1.0 24 172.16.0.2 - trunk口用于同vlan不同交换机间通信
