交换机配置 交换机基本状态: switch: # ROM状态, 路由器是rommon> hostname> # 用户模式 hostname# # 特权模式 hostname(config)# # 全局配置模式 hostname(config-if)# # 接口状态 交换机口令设置: switch>enable # 进入特权模式 switch#config terminal # 进入全局配置模式 switch(config)#hostname xxx # 设置交换机的主机名 switch(config)#enable secret xxx # 设置特权加密口令 switch(config)#enable password xxx # 设置特权非密口令 switch(config)#line console 0 # 进入控制台口 switch(config-line)#line vty 0 4 # 进入虚拟终端 switch(config-line)#login # 允许登录 switch(config-line)#password xx # 设置登录口令xx switch#exit # 返回命令 交换机VLAN设置: switch#vlan database # 进入VLAN设置 switch(vlan)#vlan 2 # 建VLAN 2 switch(vlan)#no vlan 2 # 删vlan 2 switch(config)#int f0/1 # 进入端口1 switch(config-if)#switchport access vlan 2 # 当前端口加入vlan 2 switch(config-if)#switchport mode trunk # 设置为干线 switch(config-if)#switchport trunk allowed vlan 1,2 # 设置允许的vlan switch(config-if)#switchport trunk encap dot1q # 设置vlan 中继 switch(config)#vtp domain # 设置vtp域名 switch(config)#vtp password xxx # 设置vtp密码 switch(config)#vtp mode server # 设置发vtp模式 switch(config)#vtp mode client # 设置接收vtp模式 交换机显示命令: switch#write # 保存配置信息 switch#show vtp # 查看vtp配置信息 switch#show run # 查看当前配置信息 switch#show vlan # 查看vlan配置信息 switch#show interface # 查看端口信息 switch#show int f0/0 # 查看指定端口信息 将端口加入到某个VLAN中 Switch#config termianl Switch(config)#interface f0/9 # 进入端口9的配置模式 Switch(config-if)#switchport mode access # 设置端口为静态VLAN访问模式 Switch(config-if)#switchport access vlan2 # 把端口9分配给相信的VLAN2 Switch(config-if)#exit Switch(config)#interface f0/10 Switch(config-if)#switchport mode access Switch(config-if)#switchport access vlan3 Switch(config-if)#exit Switch(config)#exit Switch#show vlan # 查看VLAN配置信息 配置STP权值 Switch1#config terminal Switch1(config)#interface f0/23 # 进入端口23配置模式,Trunk1 Switch1(config-if)#spanning-tree vlan 1 port-priority 10 # 将VLAN1的端口权值设置为10 Switch1(config-if)#spanning-tree vlan 2 port-priority 10 # 将VLAN2的端口权值设置为10 Switch1(config-if)#exit Switch1(config)#interface f0/24 # 进入端口24配置模式,Trunk2 SWitch1(config-if)#spanning-tree vlan 3 port-priority 10 # 将VLAN3的端口权值设置为10 SWitch1(config-if)#spanning-tree vlan 4 port-priority 10 # 将VLAN4的端口权值设置为10 SWitch1(config-if)#spanning-tree vlan 5 port-priority 10 # 将VLAN5的端口权值设置为10 Switch1(config-if)#end Switch1#copy running-config start-config # 保存配置文件 配置STP路径值的负载均衡 Switch1#config terminal Switch1(config)#interface f0/23 # 进入端口23配置模式,Trunk Switch1(config-if)#spanning-tree vlan 3 cost 30 # 设置VLAN3生成树路径值为30 Switch1(config-if)#spanning-tree vlan 4 cost 30 # 设置VLAN4生成树路径值为30 Switch1(config-if)#spanning-tree vlan 5 cost 30 # 设置VLAN5生成树路径值为30 Switch1(config-if)#exit Switch1(config)#interface f0/24 # 进入端口24配置模式,Trunk2 Switch1(config-if)#spanning-tree vlan 1 cost 30 # 设置VLAN1生成树路径值为30 Switch1(config-if)#spanning-tree vlan 2 cost 30 # 设置VLAN2生成树路径值为30 Switch1(config-if)#end 路由器配置 路由器显示命令: router#show run # 显示配置信息 router#show interface # 显示接口信息 router#show ip route # 显示路由信息 router#show cdp nei # 显示邻居信息 router#reload # 重新起动 路由器口令设置: router>enable # 进入特权模式 router#config terminal # 进入全局配置模式 router(config)#hostname # 设置交换机的主机名 router(config)#enable secret xxx # 设置特权加密口令 router(config)#enable password xxx # 设置特权非密口令 router(config)#line console 0 # 进入控制台口 router(config-line)#line vty 0 4 # 进入虚拟终端 router(config-line)#login # 要求口令验证 router(config-line)#password xx # 设置登录口令xx router(config)#(Ctrl+z) # 返回特权模式 router#exit # 返回命令 路由器配置: router(config)#int s0/0 # 进入Serail接口 router(config-if)#no shutdown # 激活当前接口 router(config-if)#clock rate 64000 # 设置同步时钟 router(config-if)#ip address x.x.x.x 255.255.255.255 # 设置IP地址 router(config-if)#ip address second # 设置第二个IP router(config-if)#int f0/0.1 # 进入子接口 router(config-subif.1)#ip address x.x.x.x 255.255.255.255 # 设置子接口IP router(config-subif.1)#encapsulation dot1q # 绑定vlan中继协议 router(config)#config-register 0x2142 # 跳过配置文件 router(config)#config-register 0x2102 # 正常使用配置文件 router#reload # 重新引导 路由器文件操作: router#copy running-config startup-config ;保存配置 router#copy running-config tftp ;保存配置到tftp router#copy startup-config tftp ;开机配置存到tftp router#copy tftp flash: ;下传文件到flash router#copy tftp startup-config;下载配置文件 ROM状态: Ctrl+Break ;进入ROM监控状态 rommon>confreg 0x2142 ;跳过配置文件 rommon>confreg 0x2102 ;恢复配置文件 rommon>reset ;重新引导 rommon>copy xmodem: flash: ;从console传输文件 rommon>IP_ADDRESS=10.65.1.2 ;设置路由器IP rommon>IP_SUBNET_MASK=255.255.0.0 ;设置路由器掩码 rommon>TFTP_SERVER=10.65.1.1 ;指定TFTP服务器IP rommon>TFTP_FILE=c2600.bin ;指定下载的文件 rommon>tftpdnld ;从tftp下载 rommon>dir flash: ;查看闪存内容 rommon>boot ;引导IOS 静态路由: router(config)#ip route # 命令格式 router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 # 静态路由 router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 # 默认路由 动态路由: router(config)#ip routing # 启动路由转发 router(config)#router rip # 启动RIP路由协议。 router(config-router)#network xxx... # 设置发布路由 router(config-router)#negihbor # 点对点帧中继用。 配置OSPF协议(最短开放路径协议) 命令router ospf process-id # 指定使用ospf协议 如:router ospf 100 network address wildcard-mask area area-id # 指定与该路由器相连的网络 如:network 192.200.10.4 0.0.0.3 area 0 show ip route # 查看路由表信息 show ip route ospf # 查看OSPF协议路由信息 配置EIGRP协议 命令router eigrp process-id network address wildcard-mask # 指定与该路由器相连的网络 如:network 192.200.10.0 0.0.0.3 帧中继命令: router(config)#frame-relay switching # 使能帧中继交换 router(config-s0)#encapsulation frame-relay # 使能帧中继 router(config-s0)#fram-relay lmi-type cisco # 设置管理类型 router(config-s0)#frame-relay intf-type DCE # 设置为DCE router(config-s0)#frame-relay dlci 16 router(config-s0)#frame-relay local-dlci 20 # 设置虚电路号 router(config-s0)#frame-relay interface-dlci 16 router(config)#log-adjacency-changes # 记录邻接变化 router(config)#int s0/0.1 point-to-point # 设置子接口点对点 router#show frame pvc # 显示永久虚电路 router#show frame map # 显示映射 基本访问控制列表: router(config)#access-list permit|deny <WILD|ANY> router(config)#interface ;default:deny any router(config-if)#ip access-group in|out ;default:out 例1: router(config)#access-list 4 permit 10.8.1.1 router(config)#access-list 4 deny 10.8.1.0 0.0.0.255 router(config)#access-list 4 permit 10.8.0.0 0.0.255.255 router(config)#access-list 4 deny 10.0.0.0 0.255.255.255 router(config)#access-list 4 permit any router(config)#int f0/0 router(config-if)#ip access-group 4 in 扩展访问控制列表: access-list permit|deny icmp <DESTINATIONIP wild>[type] access-list permit|deny tcp <DESTINATIONIP wild>[port] 例3: router(config)#access-list 101 deny icmp any 10.64.0.2 0.0.0.0 echo router(config)#access-list 101 permit ip any any router(config)#int s0/0 router(config-if)#ip access-group 101 in 例3: router(config)#access-list 102 deny tcp any 10.65.0.2 0.0.0.0 eq 80 router(config)#access-list 102 permit ip any any router(config)#interface s0/1 router(config-if)#ip access-group 102 out 删除访问控制例表: router(config)#no access-list 102 router(config-if)#no ip access-group 101 in 路由器的nat配置 Router(config-if)#ip nat inside # 当前接口指定为内部接口 Router(config-if)#ip nat outside # 当前接口指定为外部接口 Router(config)#ip nat inside source static [p] <私有IP><公网IP> [port] Router(config)#ip nat inside source static 10.65.1.2 60.1.1.1 Router(config)#ip nat inside source static tcp 10.65.1.3 80 60.1.1.1 80 Router(config)#ip nat pool p1 60.1.1.1 60.1.1.20 255.255.255.0 Router(config)#ip nat inside source list 1 pool p1 Router(config)#ip nat inside destination list 2 pool p2 Router(config)#ip nat inside source list 2 interface s0/0 overload Router(config)#ip nat pool p2 10.65.1.2 10.65.1.4 255.255.255.0 type rotary Router#show ip nat translation rotary 参数是轮流的意思,地址池中的IP轮流与NAT分配的地址匹配。 overload参数用于PAT 将内部IP映射到一个公网IP不同的端口上。 外部网关协议配置: routerA(config)#router bgp 100 routerA(config-router)#network 19.0.0.0 routerA(config-router)#neighbor 8.1.1.2 remote-as 200 配置PPP验证: RouterA(config)#username password RouterA(config)#int s0 RouterA(config-if)#ppp authentication {chap|pap} PIX防火墙命令 Pix525(config)#nameif ethernet0 outside security0 # 命名接口和级别 Pix525(config)#interface ethernet0 auto # 设置接口方式 Pix525(config)#interface ethernet1 100full # 设置接口方式 Pix525(config)#interface ethernet1 100full shutdown Pix525(config)#ip address inside 192.168.0.1 255.255.255.0 Pix525(config)#ip address outside 133.0.0.1 255.255.255.252 Pix525(config)#global (if_name) natid ip-ip # 定义公网IP区间 Pix525(config)#global (outside) 1 7.0.0.1-7.0.0.15 Pix525(config)#global (outside) 1 133.0.0.1 Pix525(config)#no global (outside) 1 133.0.0.1 # 去掉设置 Pix525(config)#nat (if_name) nat_id local_ip [netmark] Pix525(config)#nat (inside) 1 0 0 内网所有主机(0代表0.0.0.0)可以访问global 1指定的外网。 Pix525(config)#nat (inside) 1 172.16.5.0 255.255.0.0 内网172.16.5.0/16网段的主机可以访问global 1指定的外网。 Pix525(config)#route if_name 0 0 gateway_ip [metric] # 命令格式 Pix525(config)#route outside 0 0 133.0.0.1 1 Pix525(config)#route inside 10.1.0.0 255.255.0.0 10.8.0.1 1 Pix525(config)#static (inside, outside) 133.0.0.1 192.168.0.8 表示内部ip地址192.168.0.8,访问外部时被翻译成133.0.0.1全局地址。 Pix525(config)#static (dmz, outside) 133.0.0.1 172.16.0.8 中间区域ip地址172.16.0.8,访问外部时被翻译成133.0.0.1全局地址。
Cisco路由器交换机基础配置
猜你喜欢
转载自www.cnblogs.com/ming-yuan/p/10425037.html
今日推荐
周排行