DALI2.0模块完美兼容DALI1.0模块，全部通过Probitlab 2.0测试。
l DALI 1.0和DALI 2.0完美兼容同个模块
深圳聚积智能科技开发有限公司Add： 深圳市宝安区西乡镇固戍绵商大厦六楼Tel:0755-36960722 Mobile:13246760327 Bruce E-Mail:[email protected]
Tel:0755-36960722 Mobile:13246760327 Bruce
E-Mail:[email protected]
IEC62386-102/2.1/Test preamble
IEC62386-102/3.1/Polarity test
IEC62386-102/3.2/Maximum and minimum system voltage
IEC62386-102/3.3/Overvoltage protection test
IEC62386-102/3.4/Current rating test
IEC62386-102/3.5/Transmitter voltages
IEC62386-102/3.6/Transmitter rising and falling edges
IEC62386-102/3.7/Transmitter bit timing
IEC62386-102/3.8/Transmitter frame timing
IEC62386-102/3.9/Receiver start-up behavior
IEC62386-102/3.10/Receiver threshold
IEC62386-102/3.11/Receiver bit timing
IEC62386-102/3.12/Extended receiver bit timing
IEC62386-102/3.13/Receiver forward frame violation
IEC62386-102/3.14/Receiver settling timing
IEC62386-102/3.15/Receiver frame timing FF-FF send twice
IEC62386-102/4.1/RESET
IEC62386-102/4.2/RESET: timeout / command in-between
IEC62386-102/4.3/Send twice timeout
IEC62386-102/4.4/Commands in-between
IEC62386-102/4.5/STORE ACTUAL LEVEL IN DTR0
IEC62386-102/4.6/SaE PERSISTENT VARIABLES
IEC62386-102/4.7/SET OPERATING MODE
IEC62386-102/4.8/SET MAX LEVEL
IEC62386-102/4.9/SET MIN LEVEL
IEC62386-102/4.10/SET SYSTEM FAILURE LEVEL
IEC62386-102/4.11/SET POWER ON LEVEL
IEC62386-102/4.12/SET FADE TIME
IEC62386-102/4.13/SET FADE RATE
IEC62386-102/4.14/SET SCENE / REMOVE FROM SCENE
IEC62386-102/4.15/ADD TO GROUP / REMOVE FROM GROUP
IEC62386-102/4.16/SET SHORT ADDRESS
IEC62386-102/4.17/SET EXTEND FADE TIME
IEC62386-102/4.18/Reset/Power-on values
IEC62386-102/4.19/DTR0 / DTR1 / DTR2
IEC62386-102/5.1/READ MEMORY LOCATION on Memory Bank 0
IEC62386-102/5.2/READ MEMORY LOCATION on Memory Bank 1
IEC62386-102/5.3/READ MEMORY LOCATION on other Memory Banks
IEC62386-102/5.4/Memory bank writing
IEC62386-102/5.5/ENABLE WRITE MEMORY: writeEnableState
IEC62386-102/5.6/ENABLE WRITE MEMORY: timeout / command in-between
IEC62386-102/5.7/RESET MEMORY BANK: timeout / command in-between
IEC62386-102/5.8/RESET MEMORY BANK
IEC62386-102/6.1/Level instructions: Basic behaviour
IEC62386-102/6.2/FADE TIME: possible values
IEC62386-102/6.3/FADE TIME: transitions
IEC62386-102/6.4/FADE TIME: fading to 0
IEC62386-102/6.5/FADE TIME: small steps fading
IEC62386-102/6.6/FADE TIME: extended fade time
IEC62386-102/6.7/FADE RATE: possible values
IEC62386-102/6.8/FADE RATE: transitions
IEC62386-102/6.9/FADE RATE: extended fade time
IEC62386-102/6.10/FADE TIME/FADE RATE: stop fading by setting MIN/MAX levels
IEC62386-102/6.11/FADE TIME/FADE RATE: stop fading
IEC62386-102/6.12/FADE TIME/FADE RATE: stop fading when a command is sent, check timing
IEC62386-102/6.13/FADE TIME/FADE RATE: stop fading during startup
IEC62386-102/6.14/Level instructions: combined instructions
IEC62386-102/6.15/Power On Level – System Failure Level combined
IEC62386-102/6.16/ENABLE DAPC SEQUENCE
IEC62386-102/6.17/GO TO LAST ACTIVE LEVEL
IEC62386-102/6.18/GO TO SCENE
IEC62386-102/6.19/Power on: level control commands
IEC62386-102/6.20/Logarithmic dimming curve
IEC62386-102/6.21/Dimming curve: DAPC
IEC62386-102/6.22/Dimming curve: UP / DOWN
IEC62386-102/6.23/Dimming curve: STEP UP / STEP DOWN
IEC62386-102/6.24/FADE TIME/EXTENDED FADE TIME: light output behaviour
IEC62386-102/6.25/EXTENDED FADE TIME: light output behaviour
IEC62386-102/6.26/Behaviour during a fade
IEC62386-102/6.27/FADE TIME/FADE RATE: fading during startup
IEC62386-102/7.1/INITIALISE - timer
IEC62386-102/7.2/TERMINATE
IEC62386-102/7.3/INITIALISE – device addressing
IEC62386-102/7.4/RANDOMISE
IEC62386-102/7.5/COMPARE
IEC62386-102/7.6/WITHDRAW
IEC62386-102/7.7/SEARCHADDRH / SEARCHADDRM / EARCHADDRL
IEC62386-102/7.8/PROGRAM SHORT ADDRESS
IEC62386-102/7.9/VERIFY SHORT ADDRESS
IEC62386-102/7.10/QUERY SHORT ADDRESS
IEC62386-102/7.11/IDENTIFY DEVICE
IEC62386-102/7.12/IDENTFY DEVICE THROUCH RECALL MIN/MAX LEVEL
IEC62386-102/8.1/QUERY STATUS – lampFailure/lampOn
IEC62386-102/8.2/QUERY STATUS – lampOn
IEC62386-102/8.3/QUERY STATUS – limitError/lampOn
IEC62386-102/8.4/QUERY STATUS – powerCycleSeen
IEC62386-102/8.5/QUERY CONTROL GEAR PPRESENT
IEC62386-102/8.6/QUERY VERSION NUMBER
IEC62386-102/8.7/PING
IEC62386-102/8.8/Broadcast unaddressed
IEC62386-102/8.9/Reserved commands: standard commands
IEC62386-102/8.10/Reserved commands: special commands
IEC62386-102/8.11/Application extend commands
IEC62386-102/8.12/Not supported device types
IEC62386-102/8.13/Removed funcionality
IEC62386-102/9.1/DTR0
IEC62386-102/9.2/NVM variables
IEC62386-102/9.3/Random address generation
IEC62386-102/9.4/Addressing 1
IEC62386-102/9.5/Addressing 2
IEC62386-102/9.6/Addressing 3