VMware内CentOS7虚拟机硬盘扩容
简介
CentOS7虚拟机原硬盘空间只分配了10GB，需要扩容到20GB。
环境：VMware 10
VMware分配空间
选中虚拟机->虚拟机设置->硬盘->实用工具->扩展->设置最大磁盘大小->点击扩展
CentOS7内部分配
可以参考：http://jingyan.baidu.com/article/54b6b9c0fc8b0b2d583b47c6.html
- 查看当前磁盘空间，/dev/mapper/cl-root硬盘空间只有8GB，打算扩容：
# df -h
Filesystem Size Used Avail Use% Mounted on /dev/mapper/cl-root 8.0G 3.8G 4.3G 47% / devtmpfs 482M 0 482M 0% /dev tmpfs 493M 0 493M 0% /dev/shm tmpfs 493M 6.7M 486M 2% /run tmpfs 493M 0 493M 0% /sys/fs/cgroup /dev/sda1 1014M 184M 831M 19% /boot tmpfs 99M 0 99M 0% /run/user/0 - 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 对新增的硬盘空间做新增分区（硬盘数没有增加，增加的是空间）
# fdisk /dev/sda
Welcome to fdisk (util-linux 2.23.2).
Changes will remain in memory only, until you decide to write them.
Be careful before using the write command.
Command (m for help): n
Partition type:
p primary (2 primary, 0 extended, 2 free)
e extended
Select (default p): p
Partition number (3,4, default 3): 3 First sector (20971520-41943039, default 20971520): Using default value 20971520 Last sector, +sectors or +size{K,M,G} (20971520-41943039, default 41943039): Using default value 41943039 Partition 3 of type Linux and of size 10 GiB is set Command (m for help): t Partition number (1-3, default 3): 3 Hex code (type L to list all codes): 8e Changed type of partition 'Linux' to 'Linux LVM' Command (m for help): p Disk /dev/sda: 21.5 GB, 21474836480 bytes, 41943040 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk label type: dos Disk identifier: 0x000bc924 Device Boot Start End Blocks Id System /dev/sda1 * 2048 2099199 1048576 83 Linux /dev/sda2 2099200 20971519 9436160 8e Linux LVM /dev/sda3 20971520 41943039 10485760 8e Linux LVM Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table. WARNING: Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8) Syncing disks. - 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 重启系统 reboot
- 查看当前分区类型，本例类型为xfs
# df -T /dev/sda1
Filesystem Type 1K-blocks Used Available Use% Mounted on
/dev/sda1 xfs 1038336 188240 850096 19% /boot- 1
- 2
- 3
- 在新磁盘上创建xfs文件系统
# mkfs.xfs /dev/sda3
meta-data=/dev/sda3 isize=512 agcount=4, agsize=655360 blks
= sectsz=512 attr=2, projid32bit=1
= crc=1 finobt=0, sparse=0 data = bsize=4096 blocks=2621440, imaxpct=25 = sunit=0 swidth=0 blks naming =version 2 bsize=4096 ascii-ci=0 ftype=1 log =internal log bsize=4096 blocks=2560, version=2 = sectsz=512 sunit=0 blks, lazy-count=1 realtime =none extsz=4096 blocks=0, rtextents=0 - 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 创建PV
# pvcreate /dev/sda3
WARNING: xfs signature detected on /dev/sda3 at offset 0. Wipe it? [y/n]: y Wiping xfs signature on /dev/sda3. Physical volume "/dev/sda3" successfully created. # pvdisplay --- Physical volume --- PV Name /dev/sda2 VG Name cl PV Size 9.00 GiB / not usable 3.00 MiB Allocatable yes (but full) PE Size 4.00 MiB Total PE 2303 Free PE 0 Allocated PE 2303 PV UUID MlRwjY-TmVF-H8PV-heSz-ALGL-Q7sp-jFU6Al "/dev/sda3" is a new physical volume of "10.00 GiB" --- NEW Physical volume --- PV Name /dev/sda3 VG Name PV Size 10.00 GiB Allocatable NO PE Size 0 Total PE 0 Free PE 0 Allocated PE 0 PV UUID 0hmgH0-0wVg-jWUW-65WX-1TYb-sUGH-6jF1qm - 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- PV加入VG，vgextend后接VG Name，本例中为cl
# vgdisplay
--- Volume group ---
VG Name cl
System ID
Format lvm2
Metadata Areas 1
Metadata Sequence No 3
VG Access read/write
VG Status resizable
MAX LV 0 Cur LV 2 Open LV 2 Max PV 0 Cur PV 1 Act PV 1 VG Size 9.00 GiB PE Size 4.00 MiB Total PE 2303 Alloc PE / Size 2303 / 9.00 GiB Free PE / Size 0 / 0 VG UUID dYdb4l-wMUh-e2xv-WiaJ-Oa52-NvdF-s5ICJC # vgextend cl /dev/sda3 - 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- VG加入LV
# lvextend -l +2559 /dev/cl/root
Size of logical volume cl/root changed from 8.00 GiB (2047 extents) to 17.99 GiB (4606 extents). Logical volume cl/root successfully resized. - 1
- 2
- 3
- 4
后两个参数“+2559”和“/dev/cl/root”来源详解：
“+2559”来自于vgdisplay命令的Free PE/Size字段
# vgdisplay
--- Volume group ---
VG Name cl
...
VG Size 18.99 GiB
PE Size 4.00 MiB
Total PE 4862 Alloc PE / Size 2303 / 9.00 GiB Free PE / Size 2559 / 10.00 GiB VG UUID dYdb4l-wMUh-e2xv-WiaJ-Oa52-NvdF-s5ICJC - 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
“/dev/cl/root”来自于lvdisplay命令的LV Path字段。
# lvdisplay
...
--- Logical volume ---
LV Path /dev/cl/root
...- 1
- 2
- 3
- 4
- 5
- 调整文件系统大小，本例中是xfs文件系统使用xfs_growfs命令调整，若其他文件系统，如ext4使用resize2fs命令，注意区分。
# xfs_growfs /dev/cl/root
meta-data=/dev/mapper/cl-root isize=512 agcount=4, agsize=524032 blks
= sectsz=512 attr=2, projid32bit=1
= crc=1 finobt=0 spinodes=0 data = bsize=4096 blocks=2096128, imaxpct=25 = sunit=0 swidth=0 blks naming =version 2 bsize=4096 ascii-ci=0 ftype=1 log =internal bsize=4096 blocks=2560, version=2 = sectsz=512 sunit=0 blks, lazy-count=1 realtime =none extsz=4096 blocks=0, rtextents=0 data blocks changed from 2096128 to 4716544 - 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
结果
/dev/mapper/cl-root从8G增加到了18G
# df -h
Filesystem Size Used Avail Use% Mounted on /dev/mapper/cl-root 18G 3.8G 15G 21% / devtmpfs 482M 0 482M 0% /dev tmpfs 493M 0 493M 0% /dev/shm tmpfs 493M 6.7M 486M 2% /run tmpfs 493M 0 493M 0% /sys/fs/cgroup /dev/sda1 1014M 184M 831M 19% /boot tmpfs 99M 0 99M 0% /run/user/0