环路检测配置

环路检测配置

原理：设备通过发送环路检测报文并检测其是否返回本设备（不要求收、发端口为同一端口）以确认是否存在环路，若某端口收到了由本设备发出的环路检测报文，就认定该端口所在链路存在环路。
特殊说明：一般关闭了stp协议会存在环路，现在华为华三设备默认启用stp协议。
拓扑如图：

三台交换机基础配置：
SWA配置:
[SWA]vlan 100
[SWA-vlan100]quit
[SWA]interface range GigabitEthernet 1/0/1 to GigabitEthernet 1/0/2
[SWA-if-range]port link-type trunk
[SWA-if-range]port trunk permit vlan 100
[SWA-if-range]quit
SWA]undo stp global enable    #关闭stp

SWB配置：
[SWB]vlan 100
[SWB-vlan100]quit
[SWB]interface range GigabitEthernet 1/0/1 to GigabitEthernet 1/0/2
[SWB-if-range]port link-type trunk
[SWB-if-range]port trunk permit vlan 100
[SWB-if-range]quit
[SWB]undo stp global enable

SWC配置：
[SWC]vlan 100
[SWC-vlan100]quit
[SWC]interface range GigabitEthernet 1/0/1 to GigabitEthernet 1/0/2
[SWC-if-range]port link-type trunk
[SWC-if-range]port trunk permit vlan 100
[SWC-if-range]quit
[SWC]undo stp global enable
----------------------------------------------
#以上配置关闭了stp，已经存在环路。

全局配置环路检测：

[SWA]loopback-detection global enable vlan 100    #全局针对VLAN100内的环路检测功能
[SWA]loopback-detection global action shutdown   #全局配置环路检测的处理模式为Shutdown模式
[SWA]loopback-detection interval-time 20    #默认30S
   #配置环路检测的时间间隔为20秒，时间之后端口自动恢复UP，然后被检测环路又会被关闭

检测日志：
%Dec 12 21:32:16:550 2019 SWA LPDT/4/LPDT_LOOPED: Loopback exists on GigabitEthernet1/0/1.
%Dec 12 21:32:16:584 2019 SWA IFNET/3/PHY_UPDOWN: Physical state on the interface GigabitEthernet1/0/1 changed to down.
%Dec 12 21:32:16:587 2019 SWA IFNET/5/LINK_UPDOWN: Line protocol state on the interface GigabitEthernet1/0/1 changed to down.
%Dec 12 21:32:16:609 2019 SWA LPDT/4/LPDT_VLAN_LOOPED: Loopback exists on GigabitEthernet1/0/1 in VLAN 100.
%Dec 12 21:32:16:611 2019 SWA LPDT/5/LPDT_VLAN_RECOVERED: Loopback on GigabitEthernet1/0/1 in VLAN 100 recovered.
%Dec 12 21:32:16:613 2019 SWA LPDT/5/LPDT_RECOVERED: Loopback on GigabitEthernet1/0/1 recovered.
%Dec 12 21:32:16:633 2019 SWA LPDT/4/LPDT_LOOPED: Loopback exists on GigabitEthernet1/0/2.
%Dec 12 21:32:16:698 2019 SWA IFNET/3/PHY_UPDOWN: Physical state on the interface GigabitEthernet1/0/2 changed to down.
%Dec 12 21:32:16:703 2019 SWA IFNET/5/LINK_UPDOWN: Line protocol state on the interface GigabitEthernet1/0/2 changed to down.
%Dec 12 21:32:16:710 2019 SWA IFNET/3/PHY_UPDOWN: Physical state on the interface Vlan-interface100 changed to down.
%Dec 12 21:32:16:714 2019 SWA IFNET/5/LINK_UPDOWN: Line protocol state on the interface Vlan-interface100 changed to down.
%Dec 12 21:32:16:732 2019 SWA LPDT/4/LPDT_VLAN_LOOPED: Loopback exists on GigabitEthernet1/0/2 in VLAN 100.
%Dec 12 21:32:16:733 2019 SWA LPDT/5/LPDT_VLAN_RECOVERED: Loopback on GigabitEthernet1/0/2 in VLAN 100 recovered.
%Dec 12 21:32:16:733 2019 SWA LPDT/5/LPDT_RECOVERED: Loopback on GigabitEthernet1/0/2 recovered.


查看端口关闭由于有环路自动关闭：
[SWA]display interface GigabitEthernet 1/0/1
GigabitEthernet1/0/1
Current state: DOWN (Loopback detection down)
Line protocol state: DOWN
IP packet frame type: Ethernet II, hardware address: 4871-d643-0100
Description: GigabitEthernet1/0/1 Interface
Bandwidth: 1000000 kbps
Loopback is not set
Unknown-speed mode, unknown-duplex mode
Link speed type is autonegotiation, link duplex type is autonegotiation
Flow-control is not enabled
Maximum frame length: 9216

[SWA]display interface GigabitEthernet 1/0/2
GigabitEthernet1/0/2
Current state: DOWN(Loopback detection down)
Line protocol state: DOWN
IP packet frame type: Ethernet II, hardware address: 4871-d643-0100
Description: GigabitEthernet1/0/2 Interface
Bandwidth: 1000000 kbps
Loopback is not set
Unknown-speed mode, unknown-duplex mode
Link speed type is autonegotiation, link duplex type is autonegotiation
Flow-control is not enabled
Maximum frame length: 9216


----------------------------------------------------------------------------------------------

二层以太网接口配置环路检测：

[SWA]loopback-detection interval-time 20      #检测间隔30秒
[SWA]interface GigabitEthernet 1/0/1
[SWA-GigabitEthernet1/0/1]loopback-detection enable vlan 100
[SWA-GigabitEthernet1/0/1]loopback-detection action shutdown
[SWA-GigabitEthernet1/0/1]quit

[SWA]display loopback-detection
Loopback detection is enabled.
Loopback detection interval is 20 second(s).
Loopback is detected on following interfaces:
Interface Action mode
GigabitEthernet1/0/2 none
--------------------------------------------------------------------------------------