IPv6 路由－OSPFv3
实验目的
1. 掌握 OSPFv3 的配置方法
2. 掌握在帧中继环境下 OSPFv3 的配置方法
3. 掌握 OSPFv3 NSSA 的配置方法
4. 掌握外部路由汇总的配置
5. 掌握区域间路由的汇总配置
实验拓扑图
IPv4地址表
| Device |
Interface |
IP Address |
| R1 |
F 0/0 |
10.1.99.1 |
| S 0/0 |
192.168.99.1 |
|
| R3 |
S 0/0 |
192.168.99.3 |
| R4 |
S 0/0 |
192.168.99.4 |
| R5 |
F 0/0 |
10.1.99.5 |
| S 0/0 |
12.1.99.5 |
|
| R6 |
F 0/0 |
10.1.99.6 |
| F 0/1 |
11.1.99.6 |
|
| R8 |
F 0/1 |
11.1.99.8 |
| S 0/0 |
12.1.99.8 |
R2(config)#frame-relay switching
R2(config)#int s 0/0
R2(config-if)#no shutdown
R2(config-if)#clock rate 128000
R2(config-if)#encapsulation frame-relay
R2(config)#int s 0/1
R2(config-if)#no shutdown
R2(config-if)#clock rate 128000
R2(config-if)#encapsulation frame-relay
R2(config)#int s 0/2
R2(config-if)#no shutdown
R2(config-if)#clock rate 128000
R2(config-if)#encapsulation frame-relay
R2(config)#int s 0/0
R2(config-if)#frame-relay lmi-type cisco
R2(config-if)#frame-relay intf-type dce
R2(config)#int s 0/1
R2(config-if)#frame-relay lmi-type cisco
R2(config-if)#frame-relay intf-type dce
R2(config)#int s 0/2
R2(config-if)#frame-relay lmi-type cisco
R2(config-if)#frame-relay intf-type dce
R2(config)#int s 0/0
R2(config-if)#frame-relay route 103 interface s 0/1 301
R2(config-if)#frame-relay route 104 interface s 0/2 401
R2(config)#int s 0/1
R2(config-if)#frame-relay route 301 interface Serial0/0 103
R2(config)#int s 0/2
R2(config-if)#frame-relay route 401 interface Serial0/0 104
show frame-relay route检查帧中继交换机是否正常
R1(config)#int s 0/0
R1(config-if)#ip address 192.168.99.1 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#encapsulation frame-relay
R1(config-if)#frame-relay lmi-type cisco
R1(config-if)#no frame-relay inverse-arp
R1(config-if)#frame-relay map ip 192.168.99.3 103 broadcast
R1(config-if)#frame-relay map ip 192.168.99.4 104 broadcast
R3(config)#int s 0/0
R3(config-if)#ip address 192.168.99.3 255.255.255.0
R3(config-if)#no shutdown
R3(config-if)#encapsulation frame-relay
R3(config-if)#no frame-relay inverse-arp
R3(config-if)#frame-relay map ip 192.168.99.1 301 broadcast
R4(config)#int s 0/0
R4(config-if)#ip address 192.168.99.4 255.255.255.0
R4(config-if)#no shutdown
R4(config-if)#encapsulation frame-relay
R4(config-if)#no frame-relay inverse-arp
R4(config-if)#frame-relay map ip 192.168.99.1 401 broadcast
进行ping命令测试
从R1ping到R3与R4
R1#show frame-relay map
配置ospf
先配置外部路由器ospf (R5.R8)
R6(config)#router ospf 1
R6(config-router)#router-id 6.6.6.6
R6 (config-router)#area 1 nssa――配置区域 1 为 NSSA 区域
R6(config)#interface loopback 0
R6(config-if)#ip add 6.6.6.6 255.255.255.255
R6(config)#int f 0/0
R6(config-if)#ip add 10.1.99.6 255.255.255.0
R6(config-if)#no shut
R6(config-if)#ip ospf 1 area 0
R6(config-if)#int f 0/1
R6(config-if)#ip add 11.1.99.6 255.255.255.0
R6(config-if)#no shut
R6(config-if)#ip ospf 1 area 1
R6(config-if)#exit
R6(config)#router ospf 1
R6(config-router)#network 6.6.6.6 0.0.0.0 area 0
R6(config-router)#network 10.1.99.0 0.0.0.255 area 0
R6(config-router)#network 11.1.99.0 0.0.0.255 area 1
R1(config)#router ospf 1
R1(config-router)#router-id 1.1.1.1
R1(config)#interface loopback 0
R1(config-if)#ip add 1.1.1.1 255.255.255.255
R1(config)#int f 0/0
R1(config-if)#ip add 10.1.99.1 255.255.255.0
R1(config-if)#no shut
R1(config-if)#ip ospf 1 area 0
R1(config-if)#int s 0/0
R1(config-if)#ip ospf 1 area 0
R1(config-if)#exit
R1(config)#router ospf 1
R1(config-router)#network 1.1.1.1 0.0.0.0 area 0
R1(config-router)#network 10.1.99.0 0.0.0.255 area 0
R1(config-router)#network 192.168.99.0 0.0.0.255 area 0
R1(config-router)#neighbor 192.168.99.3
R1(config-router)#neighbor 192.168.99.4
配置帧中继中路由器的ospf (R4)
R3(config)#router ospf 1
R3(config-router)#router-id 3.3.3.3
R3(config-router)#exit
R3(config)#int loopback 0
R3(config-if)#ip add 3.3.3.3 255.255.255.255
R3(config-if)#ip ospf 1 area 2
R3(config-if)#int s 0/0
R3(config-if)# ip ospf 1 area 2
R3(config-if)# ip ospf priority 0
R3(config)#router ospf 1
R3(config-router)#network 3.3.3.3 0.0.0.0 area 2
R3(config-router)#network 192.168.99.0 0.0.0.255 area 2
已完成OSPFv2配置，在R1上查ospf邻居关系
R1#show ipv6 ospf neighbor
测试路由通断情况
在R5上测试得出结果如下（从内部到外部皆ping
通，实验完成）
IPV6地址规划
| Device |
Interface |
IP Address |
| R4 |
S0/0 |
2001:DB8:99:1::2/64 |
| R3 |
S0/0 |
2001:DB8:99:1::1/64 |
| R2 |
S0/0 |
2001:DB8:99:1::3/64 |
| F0/0 |
2001:DB8:99:2::1/64 |
|
| R6 |
F0/0 |
2001:DB8:99:2::2/64 |
| F0/1 |
2001:DB8:99:3::1/64 |
|
| R7 |
F0/0 |
2001:DB8:99:2::3/64 |
| F0/1 |
2001:DB8:99:4::1/64 |
|
| R8 |
F0/0 |
2001:DB8:99:3::2/64 |
| F0/1 |
2001:DB8:99:4::2/64 |
|
| F1/0 |
2001:DB8:99:5::2/64 |
|
| R5 |
F0/0 |
2001:DB8:99:5::1/64 |
在R1,R2,R3,R4,上配置帧中继，R1作为帧中继交换机
R1：
R1(config)#frame-relay switching
R1(config)#int s0/0
R1(config-if)#encapsulation frame-relay
R1(config-if)#frame-relay intf-type dce
R1(config-if)#clock rate 64000
R1(config-if)#frame-relay route 102 interface serial 0/1 201
R1(config-if)#frame-relay route 103 interface serial 0/2 301
R1(config-if)#no shutdown
R1(config)#int s0/1
R1(config-if)#encapsulation frame-relay
R1(config-if)#frame-relay intf-type dce
R1(config-if)#clock rate 64000
R1(config-if)#frame-relay route 201 interface serial 0/0 102
R1(config-if)#frame-relay route 104 interface serial 0/2 401
R1(config-if)#no shutdown
R1(config)#int s0/2
R1(config-if)#encapsulation frame-relay
R1(config-if)#frame-relay intf-type dce
R1(config-if)#clock rate 64000
R1(config-if)#frame-relay route 301 interface serial 0/0 103
R1(config-if)#frame-relay route 401 interface serial 0/1 104
R1(config-if)#no shutdown
R3：
R3(config)#ipv6 unicast-routing
R3(config)#ipv6 router ospf 1
R3(config-rtr)#router-id 1.1.1.5
R3(config-rtr)#int s0/0
R3(config-if)#ipv6 ospf 1 area 2
R3(config-if)#ipv6 enable
R3(config-if)#ipv6 address 2001:db8:99:1::1/64
R3(config-if)#encapsulation frame-relay
R3(config-if)#frame-relay map ipv6 2001:db8:99:1::2 102 broadcast
R3(config-if)#frame-relay map ipv6 2001:db8:99:1::3 103 broadcast
R3(config-if)#frame-relay map ipv6 FE80::C604:7FF:FE83:0 102 broadcast
R3(config-if)#frame-relay map ipv6 FE80::C602:7FF:FE65:0 103 broadcast
R3(config-if)#no shutdown
R4:
R4(config)#ipv6 unicast-routing
R4(config)#ipv6 router ospf 1
R4(config-rtr)#router-id 1.1.1.6
R4(config-rtr)#int s0/0
R4(config-if)#ipv6 ospf 1 area 2
R4(config-if)#ipv6 enable
R4(config-if)#ipv6 address 2001:db8:99:1::2/64
R4(config-if)#encapsulation frame-relay
R4(config-if)#frame-relay map ipv6 2001:db8:99:1::1 201 broadcast
R4(config-if)#frame-relay map ipv6 2001:db8:99:1::3 104 broadcast
R4(config-if)#frame-relay map ipv6 FE80::C603:7FF:FE74:0 201 broadcast
R4(config-if)#frame-relay map ipv6 FE80::C602:7FF:FE65:0 104 broadcast
R4(config-if)#no shutdown
R2:
R2(config)#ipv6 unicast-routing
R2(config)#ipv6 router ospf 1
R2(config-rtr)#router-id 1.1.1.1
R2(config)#int serial 0/0
R2(config-if)#ipv6 ospf 1 area 2
R2(config-if)#ipv6 enable
R2(config-if)#ipv6 address 2001:db8:99:4::3/64
R2(config-if)#encapsulation frame-relay
R2(config-if)#frame-relay map ipv6 2001:db8:99:1::1 301 broadcast
R2(config-if)#frame-relay map ipv6 2001:db8:99:1::2 401 broadcast
R2(config-if)#frame-relay map ipv6 FE80::C603:7FF:FE74:0 301 broadcast
R2(config-if)#frame-relay map ipv6 FE80::C604:7FF:FE83:0 401 broadcast
R2(config-if)#ipv6 ospf neighbor FE80::C603:7FF:FE74:0 priority 0
R2(config-if)#ipv6 ospf neighbor FE80::C604:7FF:FE83:0 priority 0
R2(config-if)#no shutdown
帧中继网络部分配置完成，R3 pingR2,R4测试结果如下：
配置R2,R6,R7的ospfv3,为area0。
R2:
R2(config)#int fastEthernet 0/0
R2(config-if)#ipv6 enable
R2(config-if)#ipv6 address 2001:db8:99:2::1/64
R2(config-if)#ipv6 ospf 1 area 0
R2(config-if)#no shutdown
R6:
R6(config)#ipv6 unicast-routing
R6(config)#ipv6 router ospf 1
R6(config-rtr)#router-id 1.1.1.2
R6(config-rtr)#exit
R6(config)#int fastEthernet 0/0
R6(config-if)#ipv6 enable
R6(config-if)#ipv6 address 2001:db8:99:2::2/64
R6(config-if)#ipv6 ospf 1 area 0
R6(config-if)#no shutdown
R7:
R7(config)#ipv6 unicast-routing
R7(config)#ipv6 router ospf 1
R7(config-rtr)#router-id 1.1.1.3
R7(config-rtr)#exit
R7(config)#int fastEthernet 0/0
R7(config-if)#ipv6 enable
R7(config-if)#ipv6 address 2001:db8:99:2::3/64
R7(config-if)#ipv6 ospf 1 area 0
R7(config-if)#no shutdown
然后查看R7在area0的ospf的邻居关系
R7#show ipv6 ospf neighbor
配置R6 F0/1,R7 F0/1,R8 F0/0 F0/1ospf area1为nssa 区域
R6:
R6(config)#ipv6 router ospf 1
R6(config-rtr)#area 1 nssa
R6(config-rtr)#int f0/1
R6(config-if)#ipv6 enable
R6(config-if)#ipv6 address 2001:db8:99:3::1/64
R6(config-if)#ipv6 ospf 1 area 1
R6(config-if)#no shutdown
R7:
R7(config)#ipv6 router ospf 1
R7(config-rtr)#area 1 nssa
R7(config-rtr)#int f0/1
R7(config-if)#ipv6 enable
R7(config-if)#ipv6 address 2001:db8:99:4::1/64
R7(config-if)#ipv6 ospf 1 area 1
R7(config-if)#no shutdown
R8:
R8(config)#ipv6 unicast-routing
R8(config)#ipv6 router ospf 1
R8(config-rtr)#router-id 1.1.1.4
R8(config-rtr)#area 1 nssa
R8(config-rtr)#int f0/0
R8(config-if)#ipv6 enable
R8(config-if)#ipv6 address 2001:db8:99:3::2/64
R8(config-if)#ipv6 ospf 1 area 1
R8(config-if)#no shutdown
R8(config-rtr)#int f0/1
R8(config-if)#ipv6 enable
R8(config-if)#ipv6 address 2001:db8:99:4::2/64
R8(config-if)#ipv6 ospf 1 area 1
R8(config-if)#no shutdown
查看R8 ospfv3路由表
到此ipv6 ospfv3部分配置完成，测试R4 ping R8成功
配置R5到R8 RIPng部分并且重分布到ospfv3
R5:
R5(config)#ipv6 unicast-routing
R5(config)#ipv6 router rip 1
R5(config)#int fastEthernet 0/0
R5(config-if)#ipv6 enable
R5(config-if)#ipv6 address 2001:Db8:99:5::1/64
R5(config-if)#ipv6 rip 1 enable
R5(config-if)#no shutdown
R8:
R8(config)#ipv6 router rip 1
R8(config)#int fastEthernet 1/0
R8(config-if)#ipv6 enable
R8(config-if)#ipv6 address 2001:Db8:99:5::2/64
R8(config-if)#ipv6 rip 1 enable
R8(config-if)#no shutdown
R8(config-if)#exit
R8(config)#ipv6 router ospf 1
R8(config-rtr)#redistribute rip 1
R8(config-rtr)#redistribute connected
R8(config-rtr)#exit
R8(config)#ipv6 router rip 1
R8(config-rtr)#redistribute ospf 1
R8(config-rtr)#redistribute connected
查看R5路由表,可获取area1,无法获取area 0和area2,可ping通R8
Ipv6的部分也做了一晚上，需要配置的地方很多很复杂，一个不小心就会配置出错，不是打错地址就是漏打什么，十分的考验耐心。配置已经到了最后的阶段，仅剩的几行代码，最后的实验结果就要出来了，可是正好十一点到了，电脑断网导致Vmware桥接模式的GNS3虚拟机IP失效了，GNS3也找不到服务器IP崩溃，我沉默了很久，放弃了再一次的配置。